ARTE
BELLEZA Y BIENESTAR
ARTESANÍA
CULTURA E HISTORIA
ENTRETENIMIENTO
MEDIO AMBIENTE
COMIDA Y BEBIDAS
INGENIERÍA INVERSA
CIENCIAS
DEPORTES
TECNOLOGÍA
TECNOLOGÍA VESTIBLE
The Sheet-of-Water Fountain Brush: Tapered Slots Part the Bristles
Woody

Creado por

Woody

6. octubre 2026NO
28
0
0
0
0

The Sheet-of-Water Fountain Brush: Tapered Slots Part the Bristles

Water dribbled onto the back of a brush stays in the bristles and never reaches the surface being washed. Frank L. Brinn of Milwaukee received US 840,604, patented 8 January 1907, for a fountain brush in which "the fluid may be delivered to the longitudinal central portion of the brush in a sheet, which when the fluid is turned on at full head will serve to separate the bristles and flush the surface to be washed": slots through the block narrow toward the bristles, fed from a cylinder on top through a tubular handle, with a cup on the handle to catch what runs down. This rung works out how the taper speeds the sheet, then cuts the slots in a scrub brush, plumbs it and compares full flow with throttled flow.
Intermedio
About 4 hours

Instrucciones

1

Sheet speed from the slot

Cargando el cuaderno de Jupyter…
2

Water through a brush's back before it

The embedded blueprint jets or soaks water through openings in a brush's back. Brinn shapes the openings into tapered slots so the water leaves as a sheet.
3

Read US 840,604

"By opening the valve at 3 to its full capacity a sheet of water will be discharged which will separate the bristles and effectively flush the surface to be washed, whether the bristles are in contact with such surface or not. By partially closing the valve at 3 the sheets of water escaping through the openings 18 are broken up by the bristles, and the water thus becomes distributed throughout the brush."
4

Cut the slots

On the scrub brush's top mark two slots 60 × 8 mm, 90 mm apart on the centre line. Drill a row of holes in each and cut it through with the coping saw.

Materiales para este paso:

Cepillo de fregarCepillo de fregar1 pieza

Herramientas necesarias:

Tornillo de bancoTornillo de banco
Taladro inalámbricoTaladro inalámbrico
Juego de brocasJuego de brocas
Segueta (sierra de marquetería)Segueta (sierra de marquetería)
Rotulador permanenteRotulador permanente
ReglaRegla
5

Taper the slots

Pare each slot with chisels so its long sides close to about 1.5 mm at the bristle face and its ends open out to 70 mm. Trim the bristles along the slot line.

Herramientas necesarias:

Juego de formones para maderaJuego de formones para madera
MartilloMartillo
Calibre digital de 6 pulgadasCalibre digital de 6 pulgadas
Cúter de precisiónCúter de precisión
6

Make the manifold

Cut 160 mm of 22 mm copper tube and cap both ends with fittings. File a 4 mm slot along its underside over both brush slots. Fit a tee in its middle for the handle.

Materiales para este paso:

Tubo de cobreTubo de cobre1 pieza
Accesorios de latónAccesorios de latón1 pieza

Herramientas necesarias:

CortatubosCortatubos
Limas (lima de mano)Limas (lima de mano)
Llave inglesa ajustableLlave inglesa ajustable
7

Seat the manifold

Bed the manifold on the brush in silicone over a rubber gasket and strap it down with an aluminium strip and four wood screws.

Materiales para este paso:

Sellador de siliconaSellador de silicona1 pieza
Plancha de cauchoPlancha de caucho1 pieza
Chapa de aluminioChapa de aluminio1 pieza
Tornillo para madera n.º 8 x 1"Tornillo para madera n.º 8 x 1"1 pieza

Herramientas necesarias:

Tijeras de chapaTijeras de chapa
Juego de destornilladoresJuego de destornilladores
Cúter de precisiónCúter de precisión
8

Handle, valve and drip cup

Fit 1.2 m of 15 mm copper tube to the tee, with a ball valve and hose connector at its top. Slide a small tin can, holed and sealed with silicone, onto the handle as a drip cup, and fit a short copper spout low on its side.

Materiales para este paso:

Tubo de cobreTubo de cobre1 pieza
Válvula de bolaVálvula de bola1 pieza
Accesorios de latónAccesorios de latón1 pieza
Cinta de PTFE para roscasCinta de PTFE para roscas1 pieza
LataLata1 pieza
Sellador de siliconaSellador de silicona1 pieza

Herramientas necesarias:

CortatubosCortatubos
Llave inglesa ajustableLlave inglesa ajustable
Taladro inalámbricoTaladro inalámbrico
Juego de brocasJuego de brocas
9

The patent drawing

US 840,604 drawing sheet, public domain (expired patent).
Paso 9 - Image 1
10

Full flow against throttled

Connect the garden hose. With the valve fully open, hold the brush 2 cm off a board and watch the sheet part the bristles; then close it half and watch the water spread through them. Time a litre into the jug each way.
Paso 10 - Image 1

Materiales para este paso:

AguaAgua1 pieza

Herramientas necesarias:

Jarra medidoraJarra medidora
CronómetroCronómetro
ReglaRegla
Manguera de jardínManguera de jardín
11

A sheet that sprays, sputters or leaks

Sheet-of-water fountain brush troubleshooting.

Flow

Loading...
12

History and honest limits

**Frank L. Brinn**, a citizen of Canada residing in Milwaukee, filed US 840,604 on 20 February 1905; it was patented 8 January 1907. His cylinder is held to the block by a plate with packing and screws, its slots feeding the slot-apertures; the handle's end carries a rubber sheath and the valve; the cup, with its spout, collects the water instead of letting it run down the handle when the brush is raised. **Honest limits.** A slotted copper tube stands in for his cylinder, and a tin can for his cup. The notebook treats the sheet as uniform. What you see on the board is the result.

Materiales

11

Herramientas requeridas

18

CC0 Dominio público

Este Blueprint se publica bajo CC0. Eres libre de copiar, modificar, distribuir y usar este trabajo para cualquier propósito, sin pedir permiso.

Apoya al Maker comprando productos a través de su Blueprint, donde gana una Comisión del Maker establecida por los vendedores, o crea una nueva iteración de este Blueprint e inclúyela como conexión en tu propio Blueprint para compartir ingresos.

Discusión

(0)

Iniciar sesión para unirte a la discusión

Cargando comentarios...