ARTE
BELLEZA Y BIENESTAR
ARTESANÍA
CULTURA E HISTORIA
ENTRETENIMIENTO
MEDIO AMBIENTE
COMIDA Y BEBIDAS
INGENIERÍA INVERSA
CIENCIAS
DEPORTES
TECNOLOGÍA
TECNOLOGÍA VESTIBLE
Three-Piece Airlock, 3D Printed in PETG
3DBonanza

Creado por

3DBonanza

18. noviembre 2026US
7
0
0
1
0

Three-Piece Airlock, 3D Printed in PETG

An airlock lets the carbon dioxide of a fermenting beer, wine or cider out through a little water, and keeps outside air out. This one has the four parts of the "standard type device" named in L. P. Beadle's 1980 US patent 4,218,964: a cap, a tapered stem, a housing two-thirds full of water, and a cone member. It prints in three pieces in PETG. All sizes are ours, and we have not printed or tested it yet: the leak test below comes first.
Principiante
About 5 hours, mostly printing

Instrucciones

1

Seal pressure and water back-flow

Cargando el cuaderno de Jupyter…
2

Read US 4,218,964

"Housing 27 is filled two-thirds full with water, cone 28 is inserted and cap 25 is secured ... excess gas escapes by bubbling through the water in lock 14 so as to protect the beer ingredients within container 11 from contact with outside air." The picture is our section: gas goes up the stem, under the cone member's rim and out of the cap.
Paso 2 - Image 1
3

Print the housing and stem

Stand it on the stem's tip with a 10 mm brim; the 45 degree cone under the floor needs no supports. PETG sold for food contact, a stainless steel nozzle (brass nozzles can contain lead), 0.2 mm layers, at least 4 walls so no water finds a path between the layers.
Archivo de DisenoSTLCC0 - Free

Materiales para este paso:

Filamento PETGFilamento PETG15 g

Herramientas necesarias:

Impresora 3D de filamento (FDM)Impresora 3D de filamento (FDM)
Juego de boquillas para impresora 3DJuego de boquillas para impresora 3D
4

Print the cone member

Print it upside down, closed end on the bed. PETG sold for food contact, a stainless steel nozzle (brass nozzles can contain lead), 0.2 mm layers, at least 4 walls so no water finds a path between the layers.
Archivo de DisenoSTLCC0 - Free

Materiales para este paso:

Filamento PETGFilamento PETG3 g

Herramientas necesarias:

Impresora 3D de filamento (FDM)Impresora 3D de filamento (FDM)
Juego de boquillas para impresora 3DJuego de boquillas para impresora 3D
5

Print the cap

Print it upside down, top on the bed. PETG sold for food contact, a stainless steel nozzle (brass nozzles can contain lead), 0.2 mm layers, at least 4 walls so no water finds a path between the layers.
Archivo de DisenoSTLCC0 - Free

Materiales para este paso:

Filamento PETGFilamento PETG3 g

Herramientas necesarias:

Impresora 3D de filamento (FDM)Impresora 3D de filamento (FDM)
Juego de boquillas para impresora 3DJuego de boquillas para impresora 3D
6

Clean the parts

Take off the brim. Turn a 5 mm drill bit through the stem by hand to clear any strings. Check the stem: 10.0 mm at the top, 8.5 mm at the tip.

Herramientas necesarias:

Juego de brocasJuego de brocas
Calibre digital de 6 pulgadasCalibre digital de 6 pulgadas
7

Leak test

Fill the housing with water to the groove. Stand it in a dry glass for an hour. Any drop on the outside or in the glass means a leak: print again.

Herramientas necesarias:

AguaAgua
8

Sanitise

Soak all three parts in no-rinse sanitiser mixed as its label says. Do not boil them: PETG softens at about 80 °C.

Herramientas necesarias:

DesinfectanteDesinfectante
AguaAgua
9

Assemble and fill

Drop the cone member over the riser tube. Fill the housing to the groove with sanitiser solution, not plain water. Push the cap on.

Herramientas necesarias:

DesinfectanteDesinfectante
AguaAgua
10

Fit it to the fermenter

Push the stem into the bored stopper or the lid's hole. The stem gets thinner towards the tip, so it wedges tight, as in Beadle's patent. Gas must bubble through the water, never round the stem.

Herramientas necesarias:

Tapones de gomaTapones de goma
11

Troubleshooting

Airlock problems and fixes.

Flow

Loading...
12

History and honest limits

**Leigh P. Beadle**, US 4,218,964, "Lid construction for fermentation container", filed 21 May 1979, issued 26 August 1980, assigned to Specialty Products International Ltd. His invention was the lid; he calls the airlock "a standard type device" and names its parts: cap 25, tapered stem 26, housing 27 and cone member 28. He gives no sizes and no material for the lock. Ours: every size, the riser tube, the three ribs, the vent holes, the posts that stop the cone member lifting more than 3.4 mm, and PETG. Checked in CAD for fit; not yet printed or brewed with by us.

Materiales

1

Herramientas requeridas

7

Archivos de diseño

3

CC0 Dominio público

Este Blueprint se publica bajo CC0. Eres libre de copiar, modificar, distribuir y usar este trabajo para cualquier propósito, sin pedir permiso.

Apoya al Maker comprando productos a través de su Blueprint, donde gana una Comisión del Maker establecida por los vendedores, o crea una nueva iteración de este Blueprint e inclúyela como conexión en tu propio Blueprint para compartir ingresos.

Discusión

(0)

Iniciar sesión para unirte a la discusión

Cargando comentarios...