Colaboración
ARTE
BELLEZA Y BIENESTAR
ARTESANÍA
CULTURA E HISTORIA
ENTRETENIMIENTO
MEDIO AMBIENTE
COMIDA Y BEBIDAS
INGENIERÍA INVERSA
CIENCIAS
DEPORTES
TECNOLOGÍA
TECNOLOGÍA VESTIBLE
Wheelbarrow: a Small Wooden Barrow (Cassell's, 1900)
Paul N. Hasluck (ed.) · Public domain (published 1900)
Woody

Creado por

Woody

4. noviembre 2026NO
7
0
0
0
0

Wheelbarrow: a Small Wooden Barrow (Cassell's, 1900)

A small wooden wheelbarrow: ash hales (handles) framed with oak cross-pieces, splayed legs, a red-deal bottom and sides with a curved front board bound in hoop iron, and a 1 ft wheel of eight oak spokes and four ash felloes on an ash or oak axle. Painted red inside and light green outside, lined in a lighter colour and black. Source: P. N. Hasluck, Cassell's Cyclopaedia of Mechanics (1900), p. 176. Picture: the book's Figs. 1-2.
Intermedio
Unknown

Instrucciones

1

Make the hales

Cut the two ash hales 3 ft 1 in long, 1 5/8 in deep by 1 1/2 in thick, the handles rising 3 3/4 in above the underside. Leave no more than 5/8 in on the faces of the hale tops; dress out 3/8 in on the face and 1/4 in underneath.

Materiales para este paso:

Tabla de fresnoTabla de fresno1 hales 3 ft 1 in x 1 5/8 x 1 1/2 in

Herramientas necesarias:

SerruchoSerrucho
Cepillo de carpinteroCepillo de carpintero
Cuchilla de dos manosCuchilla de dos manos
2

Frame with oak cross-pieces

Make the cross-pieces of oak, edges dressed off underneath. Let the hind piece's tenons, gauged 1/2 in thick, come through the hales 1 1/4 in to support the legs (Fig. 2). Pin the hales and cross-pieces tight with 3/16 in wood pins.

Materiales para este paso:

Tabla de roble blancoTabla de roble blanco1 pieza
Espiga de maderaEspiga de madera1 3/16 in pins

Herramientas necesarias:

Serrucho de costillaSerrucho de costilla
Formón de mortajaFormón de mortaja
GramilGramil
Berbiquí y barrenaBerbiquí y barrena
Falsa escuadraFalsa escuadra
3

Fit the legs and stays

Put on legs 1 1/2 in square, splayed at the top, standing 1 ft below the hales to suit a 1 ft wheel, with no more than a 1/4 in shoulder. Fasten legs to hales with 3 in bolts, heads outside. Fit four stays: two under the hales and two under the hind cross-pieces.

Materiales para este paso:

Tabla de roble blancoTabla de roble blanco1 legs 1 1/2 in square, stays
Tornillo de carruajeTornillo de carruaje4 3 in

Herramientas necesarias:

SerruchoSerrucho
Berbiquí y barrenaBerbiquí y barrena
Juego de destornilladoresJuego de destornilladores
4

Bottom and sides

Put in the bottom board of 1/2 in red deal, overhanging the front cross-piece 5/8 in; paint all joints. Fit the sides to the hales, the front leaning up to 3 3/4 in beyond square; sides 9 in deep by 5/8 in thick, reduced to 8 1/4 in at the hind ends, front ends edged. Run a 3/16 in or 1/4 in bead on the edge.

Materiales para este paso:

Tabla de pinoTabla de pino1 1/2 in bottom, 5/8 in sides
Pintura al óleoPintura al óleo1 pieza

Herramientas necesarias:

SerruchoSerrucho
Cepillo de carpinteroCepillo de carpintero
Juego de pincelesJuego de pinceles
5

Front board and ironwork

Fit the front board, of 3/4 in red deal or elm, on top of the hales and bottom board, rising in a curve 1 1/4 in above the sides. Paint the joints and nail the sides to it with 1 1/2 in cut nails; screw on the 7/8 in hoop iron with 3/4 in round-headed screws.

Materiales para este paso:

Tabla de pinoTabla de pino1 3/4 in front board
Clavos de hierroClavos de hierro1 1 1/2 in cut nails
Pletina de acero dulcePletina de acero dulce1 7/8 in hoop iron
Tornillos para maderaTornillos para madera1 3/4 in round-headed
Pintura al óleoPintura al óleo1 pieza

Herramientas necesarias:

SerruchoSerrucho
MartilloMartillo
Juego de destornilladoresJuego de destornilladores
Juego de pincelesJuego de pinceles
6

Make the wheel

Turn an ash or oak axle 8 1/4 in long by 2 1/2 in, its ends turned down to 1 1/2 in for ferrules 1 in long; drive 3/8 in round pins into the ends to stand out 1 in. Fit eight oak spokes 3/4 in by 1/2 in and four ash felloes 1 1/4 in square, joined with four 1/4 in dowels and bevelled to take a 3/4 in by 1/8 in hoop, rounded inside.

Materiales para este paso:

Tabla de fresnoTabla de fresno1 axle and felloes
Tabla de roble blancoTabla de roble blanco1 spokes
Varilla de hierroVarilla de hierro1 3/8 in pins
Espiga de maderaEspiga de madera4 1/4 in
Pletina de acero dulcePletina de acero dulce1 3/4 x 1/8 in tyre

Herramientas necesarias:

Torno de maderaTorno de madera
Cuchilla de dos manosCuchilla de dos manos
Berbiquí y barrenaBerbiquí y barrena
MartilloMartillo
7

Hang the wheel and paint

Screw under each hale an iron 3/4 in broad by 1/8 in thick, long enough to pass the front cross-piece by 2 or 3 in, its eye taking the axle pin. Paint the wheel and the inside of the barrow red, the outside light green, lined in a lighter colour and black.

Materiales para este paso:

Pletina de acero dulcePletina de acero dulce2 3/4 x 1/8 in irons
Tornillos para maderaTornillos para madera1 pieza
Pintura al óleoPintura al óleo1 pieza

Herramientas necesarias:

Juego de destornilladoresJuego de destornilladores
Juego de pincelesJuego de pinceles

Materiales

10

Herramientas requeridas

12

Este plano hace

Thumbnail
Marcador

Carretilla

Free

78
0

CC0 Dominio público

Este Blueprint se publica bajo CC0. Eres libre de copiar, modificar, distribuir y usar este trabajo para cualquier propósito, sin pedir permiso.

Apoya al Maker comprando productos a través de su Blueprint, donde gana una Comisión del Maker establecida por los vendedores, o crea una nueva iteración de este Blueprint e inclúyela como conexión en tu propio Blueprint para compartir ingresos.

Discusión

(0)

Iniciar sesión para unirte a la discusión

Cargando comentarios...