Collaboration
ART
BEAUTÉ ET BIEN-ÊTRE
ARTISANAT
CULTURE ET HISTOIRE
DIVERTISSEMENT
ENVIRONNEMENT
NOURRITURE ET BOISSONS
INGÉNIERIE INVERSE
SCIENCES
SPORTS
TECHNOLOGIE
TECHNOLOGIE PORTABLE
Ash Snowshoes: Steam-Bent Frame, Mortised Cross Bars and Rawhide Filling (Boy Mechanic, 1915)
Woody

Créé par

Woody

13. novembre 2026NO
4
0
0
0
0

Ash Snowshoes: Steam-Bent Frame, Mortised Cross Bars and Rawhide Filling (Boy Mechanic, 1915)

Stillman Taylor's snowshoes from The Boy Mechanic, Book 2 (1915): a white ash frame steamed and bent on a board form, two mortised cross bars set so the heel is a little heavier, and a rawhide filling woven on a lanyard, coarse in the centre and finer at toe and heel. He recommends style B, about 12 in by 42 in, for one all-round pair.
Avancé
About 2 weeks (frames dry a week)

Consignes

1

His sizes in centimetres

Chargement du notebook Jupyter…
2

Read The Boy Mechanic, Book 2

"For the frames, white ash is much the best wood, but hickory and white birch are dependable substitutes, if the former cannot be obtained." Choose the style first: style B, "the ordinary eastern model", is about 12 in wide and 42 in long, with about 2 in turn at the toe; he advises a flat toe, or a turn not over 1 in, for one all-round pair.
3

Cut the frame sticks

From seasoned white ash, saw and plane two frame sticks about 1-1/16 in wide, 7/16 in thick at the toe and 9/16 in thick at the heel (make green wood heavier, for shrinkage). Cut each 2 in longer than the finished length. The toe of the finished frame is the centre of the stick, the heel the two ends, and the centre of the shoe halfway between.

Matériaux pour cette étape :

Planche de bois durPlanche de bois dur1 pièce

Outils nécessaires :

Scie égoïneScie égoïne
RabotRabot
VastringueVastringue
CrayonCrayon
Mètre rubanMètre ruban
4

Make the bending form

Draw the shoe outline on paper, cut it out, and trace it on a board. Nail the inside blocks in place on the line; drive nails part-way into the outside stay blocks so they can be fixed quickly once the hot frame is on the form. Two forms, made exactly alike, let both frames be bent at once.

Matériaux pour cette étape :

Planche de pinPlanche de pin1 pièce
ClousClous1 pièce

Outils nécessaires :

Papier kraftPapier kraft
CrayonCrayon
CiseauxCiseaux
Scie égoïneScie égoïne
MarteauMarteau
5

Steam and bend the frame

Put boiling water in a wash boiler, lay the stick over the top and mop it with the boiling water, shifting it until the fibres soften. After 10 or 15 minutes, wrap it in cloth and bend it back and forth; repeat until it bends easily without splintering. Soften the toe well, as it is the sharpest curve. Put the hot frame on the form, bend it slowly against the inside blocks starting at the toe, nail on the outside blocks, finish one side, then the other. Leave it on the form for at least a week, until thoroughly dry and set.

Matériaux pour cette étape :

Toile de cotonToile de coton1 pièce

Outils nécessaires :

Grande marmiteGrande marmite
Balai à frangesBalai à franges
MarteauMarteau
6

Close the tail and fit the cross bars

When dry, fasten the tail by boring three holes about 4 in from the end and lashing with rawhide. Spring the two cross bars into the frame about 15 in apart and balance the shoe in your hands at the centre; when it balances exactly, move the bars so the heel is about 3 oz heavier than the toe, and mark the mortises. Cut them a good tight fit with a small, sharp chisel; 1/4 in deep is ample.

Matériaux pour cette étape :

Planche de bois durPlanche de bois dur1 pièce
Lanières de cuir vertLanières de cuir vert1 pièce

Outils nécessaires :

Chignole à mainChignole à main
Ciseaux à boisCiseaux à bois
Scie égoïneScie égoïne
Balance à fléauBalance à fléau
CrayonCrayon
7

Lace the lanyard

Bore pairs of small holes obliquely in the toe and heel sections of the frame and lace a narrow rawhide thong through them as the lanyard. Bore three holes in each cross bar, one on each side about 1-1/2 in from the frame and one in the centre, and carry the lanyard through them.

Matériaux pour cette étape :

Lacet de cuir brutLacet de cuir brut1 pièce

Outils nécessaires :

Chignole à mainChignole à main
Couteau à cuirCouteau à cuir
8

Weave the toe and heel

Make a wooden bodkin about 1/4 in thick and 2 in long to pull the strands taut. Make an eye in the end of a fine thong, pass it through a lanyard loop and back through the eye as a slipknot. Start at the corner of cross bar and frame, take the strand up and twist it round the lanyard in the middle of the toe, then down to the opposite corner. Loop it round the next lanyard (No. 2) with the twisted loop knot, carry it across, make the same knot on No. 2 on the starting side, twist it round the first strand, loop under the next cross-bar lanyard, up to the toe again, and so on until the space is filled. Join thongs endlessly by cutting an eye in each end and passing each through the other. Fill the heel the same way.

Matériaux pour cette étape :

Lacet de cuir brutLacet de cuir brut1 pièce

Outils nécessaires :

Couteau à cuirCouteau à cuir
9

Weave the centre

Use heavier hide for the centre. Make the toe cord first: carry the strand across the frame five or six times, finish with a half hitch, then twist it round the cross bar to form the first toe-cord stay. Fill the centre by looping back and twisting as for the toe, but loop round the frame with a clove hitch instead of a lanyard. Leave a toe hole 4 in wide: once enough is woven, weave through the toe cord instead of round the cross bar, in and out several times. Finish by looping round the cross bar beside the toe hole, twisting down the toe-cord stay, along the toe cord to the other side, down the other stay, round the frame, and end in a clove hitch. A mesh of about 3/4 in suits the centre.

Matériaux pour cette étape :

Lanières de cuir vertLanières de cuir vert1 pièce

Outils nécessaires :

Couteau à cuirCouteau à cuir
10

Troubleshooting

Snowshoe troubleshooting.

Flow

Loading...
11

History and honest limits

From "Snowshoes: How to Make and Use Them" by Stillman Taylor, Parts I-II, in **The Boy Mechanic, Book 2**, Popular Mechanics, 1915 (Project Gutenberg 44585; checked on the archive.org scan boymechanicbook200chic2, pp. 36-45). He gives no size for the cross bars and no widths for the thongs, only that the centre strand is heavier and the toe and heel finer. He describes a simpler filling than the Indian patterns. Foot fastenings (toe strap and heel thong) are in his Part I and not made here. The tools and metric figures are ours.

Matériaux

6

Outils requis

14

Blueprints liés

Ces blueprints partagent des connaissances — techniques, matériaux ou principes

CC0 Domaine public

Ce blueprint est publié sous CC0. Vous êtes libre de copier, modifier, distribuer et utiliser ce travail pour tout usage, sans demander la permission.

Soutenez le Maker en achetant des produits via son Blueprint où il perçoit une Commission Maker définie par les Vendeurs, ou créez une nouvelle itération de ce Blueprint et incluez-le comme connexion dans votre propre Blueprint pour partager les revenus.

Commentaires

(0)

Se connecter pour participer à la discussion

Chargement des commentaires...