Collaboration
ART
BEAUTÉ ET BIEN-ÊTRE
ARTISANAT
CULTURE ET HISTOIRE
DIVERTISSEMENT
ENVIRONNEMENT
NOURRITURE ET BOISSONS
INGÉNIERIE INVERSE
SCIENCES
SPORTS
TECHNOLOGIE
TECHNOLOGIE PORTABLE
Screw-Depth Portable Router: The Motor's Threaded Casing Screws Into a Split Base, One Turn per Sixteenth (Carter, 1924)
Forge

Créé par

Forge

13. novembre 2026NO
9
0
0
0
0

Screw-Depth Portable Router: The Motor's Threaded Casing Screws Into a Split Base, One Turn per Sixteenth (Carter, 1924)

Ray L. Carter of Syracuse, New York, received US 1,514,894, dated 11 November 1924, for the portable electric router: a small high-speed motor in an insulated casing light enough to hold in one hand, with a cutter in a chuck on its shaft. The casing is threaded outside and screws into the split, threaded top of a hollow base with a flat bottom. Each turn moves the cutter 1/16 inch, and a clamp screw across the split locks it. The base is cut away so the cutter can be seen and the chips can get out. We print the casing and base in PETG at his pitch, round a small DC motor. The other sizes are ours.
Intermédiaire
About 2 days

Consignes

1

One turn, one sixteenth

Chargement du notebook Jupyter…
2

Read US 1,514,894

"In practice, the threads of the shell 3 and support 9 are preferably about one-sixteenth inch pitch, so that each revolution of the motor or support in either direction moves the tool A correspondingly."
3

Print the motor casing

The casing 3: a tube for a 42 mm motor with a 60 mm thread at 1/16 inch pitch, an 18 mm hole and air slots in its bottom, and two holes 29 mm apart for the motor's face screws. Print it bottom down. PETG, 0.2 mm layers, 40 % infill, 5 walls; no supports.
Fichier de designSTLCC0 - Free
4

Print the base

The support 9: a hollow base with a flat plate 140 mm across and an opening 50 mm wide, its sides cut away, two wings, and the split, threaded top with clamp lugs. Print it plate down. PETG, 0.2 mm layers, 40 % infill, 5 walls; no supports.
Fichier de designSTLCC0 - Free
5

Print and fit the parts

Print the casing and the base in PETG. Clean the threads and screw the casing into the base by hand; it should turn smoothly all the way. If it is tight, run it in and out a few times. Check the base's bottom is flat by rubbing it on abrasive paper on a flat board.

Matériaux pour cette étape :

Filament PETGFilament PETG1 pièce

Outils nécessaires :

Imprimante 3D à filament (FDM)Imprimante 3D à filament (FDM)
ÉbavureurÉbavureur
Pied à coulisse numérique 6 poucesPied à coulisse numérique 6 pouces
6

Motor, collet and wiring

Fit the collet adapter on the motor's shaft and tighten its set screws. Push the motor down into the casing so its face sits on the casing's bottom with the collet through the hole, and screw it in with its two M4 face screws. Solder the supply leads through a toggle switch, sleeve the joints, and lead the cable out through the casing's open top. Set the DC supply to the motor's rated voltage.

Matériaux pour cette étape :

Moteur électriqueMoteur électrique1 pièce
Adaptateur à pince pour arbre moteurAdaptateur à pince pour arbre moteur1 pièce
Vis à tête cylindrique à six pans creuxVis à tête cylindrique à six pans creux2 pièces
Interrupteur à levierInterrupteur à levier1 pièce
Fil de câblageFil de câblage1 pièce
Gaine thermorétractableGaine thermorétractable1 pièce

Outils nécessaires :

Alimentation en courant continuAlimentation en courant continu
Fer à souder électriqueFer à souder électrique
Jeu de clés AllenJeu de clés Allen
Clé à moletteClé à molette
7

Set the depth and lock it

Fit a straight bit in the collet. Screw the casing into the base until the bit's end is level with the base's bottom on a flat board, then screw it in four more turns for a 1/4 inch (6.35 mm) deep cut. Put an M5 screw through the lugs with a wing nut and tighten it, closing the split on the thread.

Matériaux pour cette étape :

Vis à tête cylindrique à six pans creuxVis à tête cylindrique à six pans creux1 pièce
Écrou papillonÉcrou papillon1 pièce

Outils nécessaires :

Coffret de fraises de défonceuseCoffret de fraises de défonceuse
Jeu de clés AllenJeu de clés Allen
Pied à coulisse numérique 6 poucesPied à coulisse numérique 6 pouces
8

Rout a groove

Clamp a board down. Hold the router by its casing and wings, base flat on the board, switch on, and move it along a clamped straightedge so the bit cuts a groove. Take deep grooves in two or three passes, a few turns deeper each time.

Outils nécessaires :

Planche de bois durPlanche de bois dur
Serre-joint à pompeSerre-joint à pompe
Lunettes de sécuritéLunettes de sécurité
9

Troubleshooting

Router troubleshooting.

Flow

Loading...
10

History and honest limits

**Ray L. Carter** of Syracuse, New York, US 1,514,894, dated 11 November 1924, filed 29 September 1923. He claimed a motor with a threaded casing, "a hollow cylinder having a split threaded portion adapted to engage the threaded portion of said casing whereby said tool may be moved relatively to the work", a plane bottom to move over the work, and means for locking. His motor ran on mains through a lamp socket at over 7,000 r.p.m.; ours is a small DC motor on a bench supply, a light-duty router. His casing was insulating material; ours is printed PETG. His fan and baffle disk are left out. The pitch is his; the other sizes are ours.

Matériaux

8

Outils requis

11

Fichiers de conception

2

CC0 Domaine public

Ce blueprint est publié sous CC0. Vous êtes libre de copier, modifier, distribuer et utiliser ce travail pour tout usage, sans demander la permission.

Soutenez le Maker en achetant des produits via son Blueprint où il perçoit une Commission Maker définie par les Vendeurs, ou créez une nouvelle itération de ce Blueprint et incluez-le comme connexion dans votre propre Blueprint pour partager les revenus.

Commentaires

(0)

Se connecter pour participer à la discussion

Chargement des commentaires...