Collaboration
ART
BEAUTÉ ET BIEN-ÊTRE
ARTISANAT
CULTURE ET HISTOIRE
DIVERTISSEMENT
ENVIRONNEMENT
NOURRITURE ET BOISSONS
INGÉNIERIE INVERSE
SCIENCES
SPORTS
TECHNOLOGIE
TECHNOLOGIE PORTABLE
Hat Pin With a Hat-Coil and a Hair-Coil, Screwed In and Out (Condra, 1906)
Forge

Créé par

Forge

13. novembre 2026NO
11
0
0
0
0

Hat Pin With a Hat-Coil and a Hair-Coil, Screwed In and Out (Condra, 1906)

Elizabeth S. Condra of Corona, California, received US 814,833, dated 13 March 1906, for a hat pin that will not work itself out of the hat. Two small coils are bent into the pin: a short one at the point that screws through the hat, and a longer one in the middle that screws into the hair. Turned in, it holds; turned the other way, it comes out. We bend it from steel wire with a glass bead for the head. All sizes are ours.
Débutant
About 1 hour

Consignes

1

How much wire

Chargement du notebook Jupyter…
2

Read US 814,833

"The insertion of the pin is accomplished with the least possible manipulation, as the hat-coil 4 is first passed through one side of the hat, then through the hair, and then through the other side of the hat."
3

Cut and straighten the wire

Cut 1.6 mm steel wire to the length from the notebook. Draw it through a fold of cloth between your fingers, or roll it under a flat board, until it is straight.

Matériaux pour cette étape :

Fil d'acierFil d'acier1 pièce

Outils nécessaires :

Pince coupantePince coupante
Mètre rubanMètre ruban
4

Sharpen the point

Hold the wire in the vice and file one end to a long, even point, turning it as you go. Finish on a sharpening stone so it slips through felt and straw without tearing them.

Outils nécessaires :

Jeu de limes aiguillesJeu de limes aiguilles
Étau d'établiÉtau d'établi
Pierre à aiguiserPierre à aiguiser
5

Bend the hat-coil

About 6 mm from the point, wind the wire two turns round a 3 mm rod, spacing them about 3 mm apart, like a small corkscrew. Bend the wire on each side back so the point and the rest of the pin run straight along the coil's middle: her "axis in line with the rod".

Outils nécessaires :

Rond en acier douxRond en acier doux
Pince à becs rondsPince à becs ronds
Pince platePince plate
6

Bend the hair-coil

At the place the notebook gives, wind five turns the same way round the same rod, in the same direction as the hat-coil, so one turn of the pin drives both. Bend the ends back in line again. Sight along the pin: the straight parts should all lie on one line.

Outils nécessaires :

Rond en acier douxRond en acier doux
Pince à becs rondsPince à becs ronds
Pince platePince plate
7

Fit the head

Cut the end square at the finished length and roughen it with sandpaper. Fill the hole of a glass bead with epoxy and push it on, her head or knob 3. It turns the pin and stops it going too far. Leave it to set as the epoxy's label says.

Matériaux pour cette étape :

Perles de verrePerles de verre1 pièce
Époxy à deux composantsÉpoxy à deux composants1 pièce

Outils nécessaires :

Pince coupantePince coupante
Papier abrasifPapier abrasif
8

Put it in

Turn the hat-coil through one side of the hat. Push the pin straight across, without turning, until the hat-coil reaches the far side. Then turn it again: one coil goes through the hat and the other into the hair, and the head comes against the hat. To take it out, turn it back the other way and draw it out.
9

Troubleshooting

Coiled hat pin troubleshooting.

Flow

Loading...
10

History and honest limits

**Elizabeth S. Condra** of Corona, California, US 814,833, dated 13 March 1906, filed 22 August 1904. She claimed "a hat-pin comprising a metal rod having one end sharpened to form a tip or point, a head at the other end, the rod being provided with a hat-coil and a hair-coil". She wrote that it will be impossible for it to work itself out of the hat "as so frequently happens with a straight pin". She gives no sizes: the steel wire, the 230 mm length, the coil size and number of turns, the glass bead and the epoxy are ours.

Matériaux

3

Outils requis

9

Blueprints liés

Ces blueprints partagent des connaissances — techniques, matériaux ou principes

CC0 Domaine public

Ce blueprint est publié sous CC0. Vous êtes libre de copier, modifier, distribuer et utiliser ce travail pour tout usage, sans demander la permission.

Soutenez le Maker en achetant des produits via son Blueprint où il perçoit une Commission Maker définie par les Vendeurs, ou créez une nouvelle itération de ce Blueprint et incluez-le comme connexion dans votre propre Blueprint pour partager les revenus.

Commentaires

(0)

Se connecter pour participer à la discussion

Chargement des commentaires...