ART
BEAUTÉ ET BIEN-ÊTRE
ARTISANAT
CULTURE ET HISTOIRE
DIVERTISSEMENT
ENVIRONNEMENT
NOURRITURE ET BOISSONS
INGÉNIERIE INVERSE
SCIENCES
SPORTS
TECHNOLOGIE
TECHNOLOGIE PORTABLE

Counter-Rotating Egg Beater: One Wheel, Two Beaters Turning Opposite Ways
A single whisk carries the egg round with it rather than cutting through it.
James F. Monroe of Fitchburg, Massachusetts, and E. P. Monroe of New York received US 23,694, dated 19 April 1859, for an egg beater: a frame clamped to a table carries a bevel wheel turned by a handle, gearing into two pinions on opposite sides of it; one turns an inner beater of bent wires, the other an outer beater round it, "in opposite directions."
This rung works out the beater speeds, then prints the crown wheel and pinions, bends the beaters, and times a beating.
Intermédiaire
About 5 hours, plus printing
Consignes
1
1
Beater speeds
Beater speeds
Chargement du notebook Jupyter…
2
2
The gear train it uses
The gear train it uses
The embedded blueprint works gear ratios and direction. Monroe takes two pinions off opposite sides of one wheel so they turn opposite ways.
3
3
Read US 23,694
Read US 23,694
"This invention consists in arranging in an adjustable frame two beaters, one inside the other, which receive motion in opposite directions by means of two pinions which gear into a large bevel wheel and on opposite sides of the same, so that by rotating the bevel wheel by means of a handle the beaters receive the required motion."
4
4
Print the gears
Print the gears
Print the 48-tooth crown wheel (/uploads/blueprints/counter-rotating-egg-beater-crown-wheel.stl) and two 12-tooth pinions (/uploads/blueprints/counter-rotating-egg-beater-pinion.stl). Print in PETG at 0.2 mm layers, 30 % infill, 4 walls.
Matériaux pour cette étape :
Filament PETG1 pièceOutils nécessaires :
Imprimante 3D à filament (FDM)5
5
Build the frame
Build the frame
Cut a plywood upright and two arms. Bolt the crown wheel to the upright on an M5 screw with washers so it turns freely, and fix a handle screw near its rim. Drill the arms 5 mm on the line through both pinions' centres.
Matériaux pour cette étape :
Panneau de contreplaqué1 pièce
Vis à métaux1 pièce
Rondelle plate1 pièce
Écrou hexagonal1 pièce
Vis à bois #8 x 1"1 pièceOutils nécessaires :
Scie à chantourner
Perceuse sans fil
Jeu de forets
Clé à molette
Jeu de tournevis6
6
Arbor and inner beater
Arbor and inner beater
Cut 200 mm of 5 mm rod. Epoxy one pinion on it to mesh at the wheel's top, and bend two wire loops 28 mm across at its lower end.
Matériaux pour cette étape :
Rond en acier doux1 pièce
Fil d'acier inoxydable1 pièce
Époxy à deux composants1 pièceOutils nécessaires :
Scie à métaux
Pince à becs ronds
Pince plate7
7
Sleeve and outer beater
Sleeve and outer beater
Glue the second pinion to a length of silicone tube sleeved loosely over the rod, meshing at the wheel's bottom. Bend two wire loops 48 mm across and fix them to the sleeve's lower end, round the inner beater.
Matériaux pour cette étape :
Fil d'acier inoxydable1 pièce
Époxy à deux composants1 pièceOutils nécessaires :
Pince à becs ronds
Pince plate
Pied à coulisse numérique 6 pouces8
8
The patent drawing
The patent drawing
US 23,694 drawing sheet, public domain (expired patent).

9
9
Beat egg whites
Beat egg whites
Clamp the frame to the table over the bowl with two egg whites. Turn the handle about once a second and time how long until they hold stiff peaks.

Matériaux pour cette étape :
Œuf2 piècesOutils nécessaires :
Grand cul-de-poule en acier inoxydable
Chronomètre10
10
Beaters that turn together, jam or clash
Beaters that turn together, jam or clash
Counter-rotating egg beater troubleshooting.
Flow
Loading...
11
11
History and honest limits
History and honest limits
**James F. Monroe** of Fitchburg, Massachusetts, and **E. P. Monroe** of New York, assignors to E. P. Monroe, received US 23,694, dated 19 April 1859, reissued 16 October 1860 (No. 1,062). The frame's fork clamps to a table with a set screw and washer. The second pinion lies loose on the arbor, driving the outer beater whose lower collar turns loosely round the arbor's end. They noted it also mixes paint.
**Honest limits.** FDM prints hold food in their layer lines, so wash well and replace when worn. A crown wheel and spur pinions stand in for his bevel gears, and a silicone sleeve for his loose pinion. Your times are the result.
Matériaux
11- 1 pièceEspace réservé
- 1 pièceEspace réservé
- 1 pièceEspace réservé
- 1 pièceEspace réservé
- 1 pièceEspace réservé
- 1 pièceEspace réservé
- 1 pièceEspace réservé
- 2 piècesEspace réservé
- 2 piècesEspace réservé
- 1 pièceEspace réservé
- 2 piècesEspace réservé
Outils requis
12- Espace réservé
- Espace réservé
- 1 vendor sell this, none ship to you yetEspace réservé
- Espace réservé
- Espace réservé
- Espace réservé
- Espace réservé
- Espace réservé
- Espace réservé
- Espace réservé
- Espace réservé
- Espace réservé
Blueprints liés
Ces blueprints partagent des connaissances — techniques, matériaux ou principes
CC0 Domaine public
Ce blueprint est publié sous CC0. Vous êtes libre de copier, modifier, distribuer et utiliser ce travail pour tout usage, sans demander la permission.
Soutenez le Maker en achetant des produits via son Blueprint où il perçoit une Commission Maker définie par les Vendeurs, ou créez une nouvelle itération de ce Blueprint et incluez-le comme connexion dans votre propre Blueprint pour partager les revenus.


