Collaboration
ART
BEAUTÉ ET BIEN-ÊTRE
ARTISANAT
CULTURE ET HISTOIRE
DIVERTISSEMENT
ENVIRONNEMENT
NOURRITURE ET BOISSONS
INGÉNIERIE INVERSE
SCIENCES
SPORTS
TECHNOLOGIE
TECHNOLOGIE PORTABLE
Twin-Saw Table: A Rip Saw and a Crosscut Saw at Opposite Corners, One Motor, Each Depth Set by Tilting the Top (Gottschalk, 1926)
Forge

Créé par

Forge

13. novembre 2026NO
8
0
0
0
0

Twin-Saw Table: A Rip Saw and a Crosscut Saw at Opposite Corners, One Motor, Each Depth Set by Tilting the Top (Gottschalk, 1926)

Charles Gottschalk of St. Paul, Minnesota, received US 1,584,028, dated 11 May 1926, for a table saw with two saws. A crosscut saw and a rip saw stand at opposite corners of one table, so either or both can be used without changing blades. An electric motor inside the frame drives both through two chains. The top is hinged twice and lifted by a hand screw at either end, which sets each saw's depth of cut on its own. A lever with wheels lets two people truck the whole machine about. The patent gives no sizes; every size here is ours.
Avancé
About 1 week

Consignes

1

Setting each saw's depth

Chargement du notebook Jupyter…
2

Read US 1,584,028

"Inasmuch as the saws are positioned fairly close to the hinges 19 and 23 the movement of the table for one of the saws does not appreciably affect the positioning of the same in regard to the other saw so that the depth of cut of either of the two saws may be adjusted independently or simultaneously if desired."
3

Frame on skids

From 45 x 95 mm pine: two skids 10, 11 1200 mm long; four uprights 12 775 mm long; two top rails 13 1300 mm long, their ends 50 mm past the uprights (17 at the rear, 18 at the front); cross rails 14, 15 between the uprights; a motor bed 52 across the skids. Glue and bolt the joints with carriage bolts, square and level, so the rails' tops stand 820 mm above the floor and 600 mm apart.

Matériaux pour cette étape :

Bois de pinBois de pin10 pièces
Boulon de carrosserieBoulon de carrosserie24 pièces
Rondelle plateRondelle plate24 pièces
Écrou hexagonalÉcrou hexagonal24 pièces
Colle à boisColle à bois1 pièce

Outils nécessaires :

Scie sauteuseScie sauteuse
Perceuse sans filPerceuse sans fil
Jeu de foretsJeu de forets
Jeu de mèches platesJeu de mèches plates
Clé à moletteClé à molette
Serre-joint à pompeSerre-joint à pompe
Équerre combinéeÉquerre combinée
Mètre rubanMètre ruban
4

Turn the two arbors

From 30 mm steel bar turn two arbors 26, 27, each 400 mm long. On one end of each turn a collar 40 mm across and 6 mm thick 30 mm from the end, and screw-cut the last 25 mm M20 on the lathe; turn a loose flange 60 mm across with a 20 mm bore for each. Drill and tap the sprockets' hubs for set screws if they have none.

Matériaux pour cette étape :

Barre ronde en acier douxBarre ronde en acier doux2 pièces
Écrou hexagonalÉcrou hexagonal4 pièces

Outils nécessaires :

Tour à métauxTour à métaux
Mandrin de tour à 3 morsMandrin de tour à 3 mors
Outil de coupe pour tourOutil de coupe pour tour
Pied à coulisse numérique 6 poucesPied à coulisse numérique 6 pouces
Scie à métauxScie à métaux
Perceuse à colonnePerceuse à colonne
Jeu de foretsJeu de forets
Jeu de tarauds et filièresJeu de tarauds et filières
Tourne-à-gaucheTourne-à-gauche
Lunettes de sécuritéLunettes de sécurité
5

Mount the arbors and the saws

Bolt two 30 mm flange bearings 28 to the outsides of the rails for each arbor, its centre 30 mm below the rails' tops: the crosscut saw's arbor 27 250 mm from the front ends, the rip saw's arbor 26 250 mm from the rear ends. Push the arbors through so the crosscut saw's threaded end stands out past the left rail and the rip saw's past the right one, seen from the front. Fix a 17-tooth #40 sprocket on each arbor between the rails. Put each 250 mm blade on its collar, the teeth at the top pointing to the front, then the loose flange, a nut and a second nut locked against it.

Matériaux pour cette étape :

Palier appliquePalier applique4 pièces
PignonPignon2 pièces
Circular Saw Blade SetCircular Saw Blade Set1 pièce
Assortiment de boulons à tête hexagonaleAssortiment de boulons à tête hexagonale16 pièces
Vis sans tête à bout cuvetteVis sans tête à bout cuvette4 pièces

Outils nécessaires :

Clé à moletteClé à molette
Jeu de clés AllenJeu de clés Allen
Perceuse sans filPerceuse sans fil
Jeu de foretsJeu de forets
6

Motor and chains

Bolt the motor 51 to its bed between the skids under the arbors, its shaft parallel to them, and fit two 17-tooth sprockets 52 on its shaft, each in line with one arbor's sprocket. Fit a #40 chain 53, 54 from each to its arbor, tensioned by sliding the motor in slotted bolt holes. Have the motor wired to a switch within reach at the front. Oil the chains.

Matériaux pour cette étape :

Moteur électriqueMoteur électrique1 pièce
PignonPignon2 pièces
Chaîne à rouleauxChaîne à rouleaux2 pièces
Interrupteur marche/arrêtInterrupteur marche/arrêt1 pièce
Huile de machineHuile de machine1 pièce

Outils nécessaires :

Clé à moletteClé à molette
Jeu de clés AllenJeu de clés Allen
7

The hinged members and the top

Cut two hardwood members 20, 21 20 x 70 mm, 1340 mm long, to lie flat on the rails; hinge their front ends to the rails' front ends 19 and let them reach 40 mm past the rear 22. Cut the 18 mm plywood top 24 1400 x 800, with a slot over each blade, and hinge its rear edge to the members' rear ends 23. Rout a square groove 35 for the crosscut guide parallel to the crosscut saw and a second groove 200 on its other side, and a groove 42 across the top for the rip guide's bar.

Matériaux pour cette étape :

Planche de bois durPlanche de bois dur2 pièces
Panneau de contreplaquéPanneau de contreplaqué1 pièce
Charnière à lameCharnière à lame4 pièces
Vis à boisVis à bois40 pièces

Outils nécessaires :

Scie sauteuseScie sauteuse
DéfonceuseDéfonceuse
Coffret de fraises de défonceuseCoffret de fraises de défonceuse
Perceuse sans filPerceuse sans fil
Jeu de foretsJeu de forets
Serre-joint à pompeSerre-joint à pompe
Équerre combinéeÉquerre combinée
Mètre rubanMètre ruban
8

The depth screws

Screw a 6 mm steel plate under each rail's projecting end, drilled and tapped M12. Run a 150 mm M12 threaded rod up through each, with a wing nut locked on its lower end as a handle. The rear pair 156 push up under the members' rear ends 22, lifting members and top on the front hinges 19: this sets the rip saw. The front pair 157 pass through holes 58 in the members and push the top alone up on its rear hinges 23: this sets the crosscut saw.

Matériaux pour cette étape :

Plat en acier douxPlat en acier doux1 pièce
Tige filetéeTige filetée4 pièces
Écrou papillonÉcrou papillon4 pièces
Écrou hexagonalÉcrou hexagonal4 pièces
Vis à boisVis à bois16 pièces

Outils nécessaires :

Scie à métauxScie à métaux
Perceuse à colonnePerceuse à colonne
Jeu de foretsJeu de forets
Jeu de tarauds et filièresJeu de tarauds et filières
Tourne-à-gaucheTourne-à-gauche
Clé à moletteClé à molette
9

The guides

Crosscut guide: a hardwood bar 39 sliding in groove 35, with an angle fence 37 pivoted on it at 36 and clamped at any angle by a wing nut 40 through an arc slot 38. Rip guide: a bar 43 sliding in groove 42, held by a hand screw 49 through a plate 50, carrying a fence 45 hinged on a bracket 44 and tilted by a wing nut 67 in an arc slot 47.

Matériaux pour cette étape :

Planche de bois durPlanche de bois dur1 pièce
Boulon de carrosserieBoulon de carrosserie4 pièces
Écrou papillonÉcrou papillon3 pièces
Plat en acier douxPlat en acier doux1 pièce

Outils nécessaires :

Scie sauteuseScie sauteuse
Perceuse sans filPerceuse sans fil
Jeu de foretsJeu de forets
Équerre combinéeÉquerre combinée
10

The truck

Pivot two hardwood arms 60, 61 to the rear ends of the skids at 66, with a wheel 62 on the end of each beyond the pivot. Their front ends 63 are handles sliding in keepers 64 on the front uprights. With the handles down, the wheels are off the floor; lift the handles and the wheels take the weight so the saw can be wheeled away.

Matériaux pour cette étape :

Planche de bois durPlanche de bois dur2 pièces
Jeu de roues en caoutchoucJeu de roues en caoutchouc1 pièce
Assortiment de boulons à tête hexagonaleAssortiment de boulons à tête hexagonale4 pièces
Vis à boisVis à bois8 pièces

Outils nécessaires :

Scie sauteuseScie sauteuse
Perceuse sans filPerceuse sans fil
Jeu de foretsJeu de forets
Clé à moletteClé à molette
11

Try it

Wind both screw pairs down and check each blade stands square to the top and parallel to its groove. Set the rip saw's depth with the rear screws and the crosscut's with the front screws, each about 10 mm above the wood. Wearing glasses and ear defenders, rip a board along the rip guide, then cut the end off another against the crosscut guide.

Outils nécessaires :

Équerre combinéeÉquerre combinée
Mètre rubanMètre ruban
Lunettes de sécuritéLunettes de sécurité
Protection auditive (casque, SNR 30 dB)Protection auditive (casque, SNR 30 dB)
12

Troubleshooting

Twin-saw table troubleshooting.

Flow

Loading...
13

History and honest limits

**Charles Gottschalk** of St. Paul, Minnesota, US 1,584,028, dated 11 May 1926, filed 1 August 1921. He claimed a frame with two rails, longitudinal members hinged to the rails at one end, a single top hinged to them at the other, a crosscut saw at one end and a rip saw at the other through the top, and means to oscillate the members and top together, and the top alone, "so as to vary the relative depth of cut of either of said saws". He says a gasoline engine may drive it instead of the motor. His grooves are dovetailed; ours are square. He gives no sizes, speeds or sprocket sizes; all of those are ours.

Matériaux

23

Outils requis

21

CC0 Domaine public

Ce blueprint est publié sous CC0. Vous êtes libre de copier, modifier, distribuer et utiliser ce travail pour tout usage, sans demander la permission.

Soutenez le Maker en achetant des produits via son Blueprint où il perçoit une Commission Maker définie par les Vendeurs, ou créez une nouvelle itération de ce Blueprint et incluez-le comme connexion dans votre propre Blueprint pour partager les revenus.

Commentaires

(0)

Se connecter pour participer à la discussion

Chargement des commentaires...