Collaboration
ART
BEAUTÉ ET BIEN-ÊTRE
ARTISANAT
CULTURE ET HISTOIRE
DIVERTISSEMENT
ENVIRONNEMENT
NOURRITURE ET BOISSONS
INGÉNIERIE INVERSE
SCIENCES
SPORTS
TECHNOLOGIE
TECHNOLOGIE PORTABLE
Cart Saddle: a Stuffed Panel, Dock, Flaps, Girths and Housings on a Bought Tree (Hasluck, Harness Making, 1904)
Tex

Créé par

Tex

13. novembre 2026FO
6
0
0
0
0

Cart Saddle: a Stuffed Panel, Dock, Flaps, Girths and Housings on a Bought Tree (Hasluck, Harness Making, 1904)

The cart saddle carries the back chain that holds up a cart's shafts. From Paul N. Hasluck's Harness Making (1904): on a bought wooden tree, a panel of lining and basil stuffed with straw and flock, a dock for the crupper, flaps, two girths and two straps, and leather housings nailed over the top. All sizes are his. It follows the cart bridle and collar; the crupper and breeching come next.
Avancé
About 3 days

Consignes

1

Girths, straps and housings

Chargement du notebook Jupyter…
2

Read Harness Making, ch. VII

"Leave the space between the middle lines of stitches about 2 in. wider in front than at the back to prevent the shoulder-bone of the horse being caught when carrying a weight."
3

Prepare the tree

For a horse about 15½ hands get a tree 14 in across the board through the centre, with an iron plate for the back chain. If the board is very long saw the same length off each end, "never at one end only"; a 1 ft board is always long enough. If the housings are to be nailed at the side, cover the top of the tree with thin leather, nailed under the housing at the lower edge, damped, rubbed down close and nailed at the very top.

Matériaux pour cette étape :

Arçon de selletteArçon de sellette1 pièce
Cuir de harnaisCuir de harnais1 pièce
ClousClous1 pièce

Outils nécessaires :

Scie égoïneScie égoïne
Mètre rubanMètre ruban
Marteau à panne fendueMarteau à panne fendue
ÉpongeÉponge
4

Cut the panel back

From the middle of each side cut the panel back about ½ in longer than the boards and 2 in wider than the board's central width, with the middle lines 2 in wider apart in front than behind. Cut both sides alike, pattern reversed, whip them together along the centre, and shorten the front by cutting from the point slanting inward and upward. Rub the stitches flat and stitch on a piece of leather about 3 in square at each board position, for nailing the panel on later.

Matériaux pour cette étape :

Cuir de harnaisCuir de harnais1 pièce
Fil de cuirFil de cuir1 pièce

Outils nécessaires :

Couteau à cuirCouteau à cuir
Deux aiguilles de sellierDeux aiguilles de sellier
AlêneAlêne
5

Line and face the panel

Lay it on flannel check or linen cut about ½ in larger, slit the lining at the front centre and whip in a widening piece; turn the extra ½ in in and run a coarse stitch round. Whip a basil facing about 2¾ in wide all round the lining, joined in the centre of each side, and cut the lining down round the back to about 2 in wide, so the stuffed panel is thicker in front. Cut the facing back about 1¼ in at the front for about 4½ in and about 2 in at the back. Tack the facing round the back, both inside out, and run it with coarse stitches about three to the inch. Damp the back and the facing with sponge and water.

Matériaux pour cette étape :

Toile de linToile de lin1 pièce
BasaneBasane1 pièce
Fil de cuirFil de cuir1 pièce

Outils nécessaires :

CiseauxCiseaux
Deux aiguilles de sellierDeux aiguilles de sellier
AlêneAlêne
ÉpongeÉponge
6

Open the gullet

Cut a lengthwise slit in the exact centre of the lining, just big enough to turn the panel. Mark a line each side of the back seam, about 1½ in each side at the back widening to about 2¼ in at the front, and tack the lining tight and flat between them. Wrap a 9 in wisp of straw in hemp, a little thicker than a finger, set its centre in the gullet at the front and stitch the facing tight round it with a spot stitch, to keep the gullet open and off the shoulder. Spot-stitch the lining along the two lines, leaving the slit open for stuffing.

Matériaux pour cette étape :

Paille de seiglePaille de seigle1 pièce
Ficelle de chanvreFicelle de chanvre1 pièce
Fil de cuirFil de cuir1 pièce

Outils nécessaires :

CiseauxCiseaux
Deux aiguilles de sellierDeux aiguilles de sellier
AlêneAlêne
7

Stuff the panel

Lay it on the bench lining up, held by stout clout nails at the corners, the slit along the bench edge. With straw cut to the panel's length and the stuffing stick, lay a wisp across the front, one across the back, then wisp after wisp along the front until the side is full; no more straw in the ends after the first wisp. Beat it level with the collar mallet. Slide a strip of leather 9 in long into the slit to clear it, lay a thick even layer of carded flock over the straw, press it to the edges and corners, beat it, and level it with the seat-awl, feeling for lumps. Do the other side the same.

Matériaux pour cette étape :

Paille de seiglePaille de seigle1 pièce
Bourre de laineBourre de laine1 pièce
ClousClous1 pièce

Outils nécessaires :

Bourroir de collierBourroir de collier
Maillet en boisMaillet en bois
AlêneAlêne
Marteau à panne fendueMarteau à panne fendue
8

Make and fit the dock

Across the back, from board to board: two 1¾ in tinned rings and leather 1½ in wide doubled to reach half the board's width each side, "better" in four thicknesses running double through the rings. Nail through each end with a clout nail clinched on a piece of iron, one or two in the centre; spot or stitch a row each side; trim, black and rub with tallow. Bore holes with a gimlet halfway between tree and board end, run two fine-pointed staples through the rings and knock them down until about ¾ in shows below; turn and clinch the points. The dock must be slack, with at least the same sweep as the tree.

Matériaux pour cette étape :

Cuir de harnaisCuir de harnais1 pièce
Anneau de harnaisAnneau de harnais2 pièces
ClousClous1 pièce
Cavalier en fil de ferCavalier en fil de fer2 pièces
Fil de cuirFil de cuir1 pièce
Teinture pour cuirTeinture pour cuir1 pièce
SuifSuif1 pièce

Outils nécessaires :

Couteau à cuirCouteau à cuir
Marteau à panne fendueMarteau à panne fendue
EnclumeEnclume
VrilleVrille
AlêneAlêne
Deux aiguilles de sellierDeux aiguilles de sellier
9

Make the flaps

Cut two flaps about 9 in deep, ½ in longer at each end at the top than the boards; swell them out at the sides, round the bottom corners and cut a fancy point in the centre of the lower side. Hold each against the board, mark the tree's width, cut slits about ¾ in deep at the marks and turn the leather between them inward. Cut a hole for a 1½ in girth or strap about the middle of each flap opposite the joint of board and tree. Edge flaps and holes, race two or three rows round, black the edges and finish with a hot iron.

Matériaux pour cette étape :

Cuir de harnaisCuir de harnais1 pièce
Teinture pour cuirTeinture pour cuir1 pièce

Outils nécessaires :

Couteau à cuirCouteau à cuir
Emporte-pièce pour cuirEmporte-pièce pour cuir
Abat-carreAbat-carre
Compas à rainer de sellierCompas à rainer de sellier
Fileteuse de sellierFileteuse de sellier
Chalumeau à propaneChalumeau à propane
10

Make the girths and straps

Cut them from good leather to the notebook's lengths, 1¼ to 1¾ in wide. Edge the girths, turn down the chapes, point the straps, leaving the best end of each for nailing to the tree. Race two rows along the edges and bevel with a hot iron. Stitch the buckles, make the loops and two running loops, finish the loops on a loop-stick and crease them. Black the edges, hot-bevel, and cut four or five holes in the straps.

Matériaux pour cette étape :

Cuir de harnaisCuir de harnais1 pièce
Boucle en fer à ardillonBoucle en fer à ardillon2 pièces
Fil de cuirFil de cuir1 pièce
Teinture pour cuirTeinture pour cuir1 pièce

Outils nécessaires :

Couteau à cuirCouteau à cuir
Abat-carreAbat-carre
Compas à rainer de sellierCompas à rainer de sellier
Fileteuse de sellierFileteuse de sellier
Mandrin à passantsMandrin à passants
Emporte-pièce pour cuirEmporte-pièce pour cuir
AlêneAlêne
Deux aiguilles de sellierDeux aiguilles de sellier
11

Nail on flaps, girths and straps

Set each flap's slit opposite the tree with about an inch of leather on the board, and drive a saddler's tack gently into each end of the board. Put the shorter strap in front and the longer behind through the flap holes from above, square ends out at the top between flap and board, and nail four or five along the flap edge, two through strap and flap, one more in the strap's centre. Fix the girths on the other side the same. Straps on the near side, girths on the off, the longer of each behind. The front of the tree is where the boards rise and converge.

Matériaux pour cette étape :

ClousClous1 pièce

Outils nécessaires :

Marteau à panne fendueMarteau à panne fendue
12

Fit the panel

Set the front of the panel against the front of the tree, pressed to the top in the centre, and fasten the nailing pieces to the boards with four or five small tacks, close; do the back the same.

Matériaux pour cette étape :

ClousClous1 pièce

Outils nécessaires :

Marteau à panne fendueMarteau à panne fendue
13

Cut and nail the housings

Cut the housings 5 to 7 in wide, long enough to reach end to end over the tree beside the groove (measure with string), the ends bulged and rounded to be 3 in more along the centre. Narrow the front housing slightly for about 10 in in the centre so it rises there; shape the back housing's nailed side from the corners up to a point in the middle. Race three rows round the edges and run them deep with a beveller. Nail each through the centre, pull it down hard from the centre with the seat-awl, and nail all along about 2 in apart, the edge flush with the tree. Cover the nails with a welt of the same width nailed down, and put seven or eight stitches, nine per inch, at the four ends through the flap.

Matériaux pour cette étape :

Cuir de harnaisCuir de harnais1 pièce
ClousClous1 pièce
Fil de cuirFil de cuir1 pièce

Outils nécessaires :

Couteau à cuirCouteau à cuir
Compas à rainer de sellierCompas à rainer de sellier
Fileteuse de sellierFileteuse de sellier
Chalumeau à propaneChalumeau à propane
AlêneAlêne
Marteau à panne fendueMarteau à panne fendue
Griffe à frapperGriffe à frapper
Deux aiguilles de sellierDeux aiguilles de sellier
14

Troubleshooting

Cart saddle troubleshooting.

Flow

Loading...
15

History and honest limits

From **Harness Making**, edited by Paul N. Hasluck, Cassell and Company, 1904, chapter VII, "Cart Saddles, Reins, etc." (Project Gutenberg #70169). All sizes are his; the tree is bought, as in the book. Not made here: the brass ovals and brass beading (his leather welt is used instead) and the 2 in strap he gives as an alternative to the dock. The crupper, breeching and the smaller straps from the same chapter are the next blueprint. The heat source for the iron and the metric figures are ours.

Matériaux

14

Outils requis

19

CC0 Domaine public

Ce blueprint est publié sous CC0. Vous êtes libre de copier, modifier, distribuer et utiliser ce travail pour tout usage, sans demander la permission.

Soutenez le Maker en achetant des produits via son Blueprint où il perçoit une Commission Maker définie par les Vendeurs, ou créez une nouvelle itération de ce Blueprint et incluez-le comme connexion dans votre propre Blueprint pour partager les revenus.

Commentaires

(0)

Se connecter pour participer à la discussion

Chargement des commentaires...