Collaboration
ART
BEAUTÉ ET BIEN-ÊTRE
ARTISANAT
CULTURE ET HISTOIRE
DIVERTISSEMENT
ENVIRONNEMENT
NOURRITURE ET BOISSONS
INGÉNIERIE INVERSE
SCIENCES
SPORTS
TECHNOLOGIE
TECHNOLOGIE PORTABLE
Hot Plate Magnetic Stirrer: Ring Heater over a Relay Magnet on a Shielded Spindle (Hug, US 3,028,476)
Ed

Créé par

Ed

9. novembre 2026FI
12
0
0
0
0

Hot Plate Magnetic Stirrer: Ring Heater over a Relay Magnet on a Shielded Spindle (Hug, US 3,028,476)

A laboratory stand that heats a vessel and stirs it at the same time. A motor in the base spins a bar magnet; in Theodore Hug's design (US 3,028,476, 1962) that magnet turns a second, free bar magnet on a spindle inside the hot plate, which in turn spins a coated stirring bar in the vessel. A stainless-steel radiation shield and an air gap keep the ring heater's heat away from the motor. The relay magnet sits about 1/2 in. under the aluminium heat sink: closer, eddy currents in the sink slow the stirring. Source: T. Hug, "Hot Plate and Magnetic Stirrer", US Patent 3,028,476 (filed 1960, granted 1962). Picture: its Figs. 1-2.
Avancé
Unknown

Consignes

1

Read Hug

"Attempts have been made to couple conventional heating means to magnetic stirrers, but the same have proved to be unsuccessful. Thus, the base of a laboratory vessel must be positioned relatively close to the driving rotating magnet ... Moreover, if an appreciable amount of heat from the heating means is transmitted to the motor of the magnetic stirrer, it will drastically reduce the useful operating life of said motor."
2

Build the stirrer base

Make a housing of aluminium (or another non-magnetic material) and mount an electric motor inside with its shaft upright. Fix a permanent bar magnet horizontally on the top of the shaft, just under the housing top. Wire the motor through a rheostat to its cord so the speed can be varied. Sizes, motor rating and how the housing is formed are not given.

Matériaux pour cette étape :

Tôle d'aluminiumTôle d'aluminium1 housing
Moteur électriqueMoteur électrique1 pièce
Jeu d'aimants droitsJeu d'aimants droits1 drive magnet
RhéostatRhéostat1 pièce
Cordon souple avec ficheCordon souple avec fiche1 pièce

Outils nécessaires :

Dimensions inconnuesDimensions inconnues
Procédé de formage inconnuProcédé de formage inconnu
3

Make the radiation shield

Shape a radiation shield of non-magnetic stainless steel so it straddles the top of the housing, on stainless-steel legs (a poor conductor of heat) that stand on the housing top. Bore its centre and fit a threaded spindle there with a nut on each side of the shield. Tap a blind thread in each leg.

Matériaux pour cette étape :

Tôle en acier inoxydable - 304Tôle en acier inoxydable - 3041 shield and legs
Tige filetéeTige filetée1 spindle
Écrou hexagonalÉcrou hexagonal2 pièces

Outils nécessaires :

Cisaille à tôleCisaille à tôle
Perceuse à colonnePerceuse à colonne
Jeu de foretsJeu de forets
Jeu de tarauds et filièresJeu de tarauds et filières
Procédé de formage inconnuProcédé de formage inconnu
4

Fit the relay magnet

Bore a blind cavity in a hub of non-magnetic material so it turns freely on the spindle. Lay a permanent bar magnet 1/4 in. by 1 in. by 1 3/4 in. on top of the hub and hold it with a strap screwed to the hub. The hub and strap material is not given.

Matériaux pour cette étape :

Jeu d'aimants droitsJeu d'aimants droits1 relay magnet, 1/4 x 1 x 1 3/4 in.
Matériau inconnuMatériau inconnu1 hub and strap
Vis à métauxVis à métaux2 pièces

Outils nécessaires :

Tour à métauxTour à métaux
Perceuse à colonnePerceuse à colonne
Jeu de foretsJeu de forets
Jeu de tarauds et filièresJeu de tarauds et filières
5

Mount the supports

Make three support members of non-magnetic stainless steel, each an upright with flanges. Screw the flanges down into the legs, with small tubular spacers of insulating material round the screws between the shield and the flanges, so air can circulate and carry heat away. Fit a grommet in one support for the heater cord. The spacer material is not given.

Matériaux pour cette étape :

Tôle en acier inoxydable - 304Tôle en acier inoxydable - 3041 three supports
Vis à métauxVis à métaux3 pièces
Isolant inconnuIsolant inconnu3 tubular spacers

Outils nécessaires :

Cisaille à tôleCisaille à tôle
Perceuse à colonnePerceuse à colonne
Jeu de foretsJeu de forets
6

Fit the heater and top

Mount an annular ring heater (elements in a non-magnetic sheath) coaxial with the spindle; join its cord wires to its threaded stud between two nuts. Above it lay an aluminium heat sink, a flat plate wider than the heater, so the relay magnet is about 1/2 in. below it. Cover with a top plate of aluminium or stainless steel whose edge is spun into an inverted dish, and screw the edge to the tops of the supports. The patent claims a blackened outer surface on the heat sink and top plate (how is not given). In use, set the hot plate on the stirrer and put a stirring bar (a short bar magnet sealed in glass or coated with PTFE) in the vessel: the drive magnet turns the relay magnet, which turns the bar.

Matériaux pour cette étape :

Élément chauffantÉlément chauffant1 ring heater
Cordon souple avec ficheCordon souple avec fiche1 pièce
Écrou hexagonalÉcrou hexagonal2 pièces
Plaque d'aluminiumPlaque d'aluminium1 heat sink
Tôle d'aluminiumTôle d'aluminium1 top plate
Vis à métauxVis à métaux3 pièces

Outils nécessaires :

Outil de repoussageOutil de repoussage
Tour à métauxTour à métaux
Perceuse à colonnePerceuse à colonne
Jeu de foretsJeu de forets

Matériaux

13

Outils requis

8

CC0 Domaine public

Ce blueprint est publié sous CC0. Vous êtes libre de copier, modifier, distribuer et utiliser ce travail pour tout usage, sans demander la permission.

Soutenez le Maker en achetant des produits via son Blueprint où il perçoit une Commission Maker définie par les Vendeurs, ou créez une nouvelle itération de ce Blueprint et incluez-le comme connexion dans votre propre Blueprint pour partager les revenus.

Commentaires

(0)

Se connecter pour participer à la discussion

Chargement des commentaires...