Collaboration
ART
BEAUTÉ ET BIEN-ÊTRE
ARTISANAT
CULTURE ET HISTOIRE
DIVERTISSEMENT
ENVIRONNEMENT
NOURRITURE ET BOISSONS
INGÉNIERIE INVERSE
SCIENCES
SPORTS
TECHNOLOGIE
TECHNOLOGIE PORTABLE
Platform Scale: Four Knife-Edge Hinges and Two Levers to a Steelyard (Fairbanks, 1831)
Mark

Créé par

Mark

2. novembre 2026FI
9
0
0
0
0

Platform Scale: Four Knife-Edge Hinges and Two Levers to a Steelyard (Fairbanks, 1831)

A scale for wagons and carts, reading the same wherever the load stands. Erastus and Thaddeus Fairbanks of St. Johnsbury, Vermont, patented it in 1831. A plank platform nine by twelve feet rests on four knife-edge hinges, one at each corner, and two levers gather the load from all four onto one rod. The rod pulls on an ordinary steelyard, which then reads only a tenth or a twentieth of the load. Result: a platform scale reading ten times (or twenty times) what the steelyard shows, the same wherever the load stands on the platform. Source: E. & T. Fairbanks, US Patent No. 118 (1837), restating their patent of 13 June 1831. Unknown: the material and sizes of the hinges, knife-edges, fulcra and levers. Picture: patent drawing.
Avancé
1 week

Consignes

1

Build the frame

Lay two timber bed-sills, about 10 inches square and 16 feet long, parallel and about 7 feet apart. Bolt two end timbers, 8 by 14 inches and 12 feet long, across them near their ends. Just inside the end timbers, lay the two rockers, 8 inches square and 9 feet long, with their tops flush with the end timbers. Ours: carriage bolts.

Matériaux pour cette étape :

Bois équarriBois équarri6 2 sills, 2 end timbers, 2 rockers
Boulon de carrosserieBoulon de carrosserie1 jeu

Outils nécessaires :

Passe-partoutPasse-partout
TarièreTarière
MarteauMarteau
2

Fit the four knife-edge hinges

Bolt a hinge firmly under each end of each rocker, one at every corner of the machine. Each hinge carries two knife-edges. One rests on a fulcrum standing on the bed-sill; the other reaches out to carry the platform. Set every knife-edge parallel to the others: knife-edges at an angle cramp and bind. Not given: the material and size of the hinges, knife-edges and fulcra.

Matériaux pour cette étape :

Matériau inconnuMatériau inconnu1 4 hinges, 8 knife-edges, 4 fulcra
Boulon de carrosserieBoulon de carrosserie1 jeu

Outils nécessaires :

TarièreTarière
Dimensions inconnuesDimensions inconnues
3

Join the levers

Run a horizontal lever from each rocker. The longer lever reaches across nearly to the opposite rocker. The shorter one ends at a point equally far from the axes of both, and hangs there from the longer lever by a chain, rod or stirrup, so the two act as one. From the end of the longer lever a rod rises straight up to a steelyard hung from a fixed support. With the two knife-edges of each hinge 6 inches apart and the rod hung 60 inches from the lever's axis, the load is ten times the steelyard reading; at 120 inches it is twenty times. Not given: the lever material. Ours: an iron chain and a wrought iron rod.

Matériaux pour cette étape :

Matériau inconnuMatériau inconnu1 2 levers
Chaîne en ferChaîne en fer1 lever link
Tige de fer forgéTige de fer forgé1 rod to the steelyard
Balance romaineBalance romaine1 pièce

Outils nécessaires :

Dimensions inconnuesDimensions inconnues
4

Lay the platform

Lay two timbers, short enough to pass freely between the rockers, parallel over the bed-sills. Spike stout planks 9 feet long across them, making a platform of about 9 by 12 feet. Under these timbers fasten iron plates that rest on the inner knife-edges of the hinges. Ours: nails as the spikes.

Matériaux pour cette étape :

Bois équarriBois équarri2 platform timbers
Planche de boisPlanche de bois1 for 9 x 12 ft
Plaque de ferPlaque de fer4 pièces
ClousClous1 as needed

Outils nécessaires :

Passe-partoutPasse-partout
MarteauMarteau

Matériaux

9

Outils requis

4

CC0 Domaine public

Ce blueprint est publié sous CC0. Vous êtes libre de copier, modifier, distribuer et utiliser ce travail pour tout usage, sans demander la permission.

Soutenez le Maker en achetant des produits via son Blueprint où il perçoit une Commission Maker définie par les Vendeurs, ou créez une nouvelle itération de ce Blueprint et incluez-le comme connexion dans votre propre Blueprint pour partager les revenus.

Commentaires

(0)

Se connecter pour participer à la discussion

Chargement des commentaires...