ART
BEAUTÉ ET BIEN-ÊTRE
ARTISANAT
CULTURE ET HISTOIRE
DIVERTISSEMENT
ENVIRONNEMENT
NOURRITURE ET BOISSONS
INGÉNIERIE INVERSE
SCIENCES
SPORTS
TECHNOLOGIE
TECHNOLOGIE PORTABLE
Push Buttons — SIK Circuit 5
Ed

Créé par

Ed

17. mars 2026FI
99
0
0
0
0

Push Buttons — SIK Circuit 5

Use two push buttons for digital input. Learn about digitalRead(), pull-up resistors, and boolean logic (AND, OR, NOT) to control an LED.

Consignes

1

Parts & Introduction

Push buttons are the simplest digital input. This experiment uses two buttons with an XOR logic gate: the LED turns on if you press either button, but turns off if you press both. You'll learn about digitalRead(), pull-up resistors, and boolean logic.

Parts Needed

  • 1x Arduino Uno + USB cable
  • 1x Breadboard
  • 2x Push Buttons
  • 1x LED (any color)
  • 1x 330Ω Resistor
  • 2x 10KΩ Resistors (pull-ups)
  • 7x Jumper Wires

Matériaux pour cette étape :

SparkFun Inventor's Kit - V3.2SparkFun Inventor's Kit - V3.21 kit

Outils nécessaires :

Ordinateur avec l'IDE ArduinoOrdinateur avec l'IDE Arduino
2

Hardware Hookup

Wiring Instructions

  1. Place both push buttons across the center canyon of the breadboard.
  2. Button 1: Connect one pin to GND. Connect the opposite diagonal pin to Arduino Digital Pin 2. Add a 10K resistor between Pin 2 and 5V (pull-up).
  3. Button 2: Connect one pin to GND. Connect the opposite diagonal pin to Arduino Digital Pin 3. Add a 10K resistor between Pin 3 and 5V (pull-up).
  4. Connect LED positive leg to Digital Pin 13, negative leg through 330Ω resistor to GND.

Note: The pull-up resistors hold the input HIGH when the button is not pressed. Pressing the button connects the pin to GND (LOW).

Matériaux pour cette étape :

Bouton-poussoirBouton-poussoir2 pièces
Plaque d'essaiPlaque d'essai1 pièce
Fils de liaisonFils de liaison7 pièces
3

Arduino Code

Open the Arduino IDE and upload the following sketch to your Arduino board.

push_buttons.inoarduino
/*
SparkFun Inventor's Kit
Example sketch 05 — PUSH BUTTONS

Use pushbuttons for digital input.
LED on if pressing button 1 OR button 2, but not both (XOR).

Hardware connections:
  Button 1: one pin to GND, diagonal pin to digital pin 2
            10K pullup resistor between pin 2 and 5V
  Button 2: one pin to GND, diagonal pin to digital pin 3
            10K pullup resistor between pin 3 and 5V
  LED: positive to pin 13, negative through 330 ohm to GND

This code is completely free for any use.
*/

const int button1Pin = 2;
const int button2Pin = 3;
const int ledPin = 13;

void setup()
{
  pinMode(button1Pin, INPUT);
  pinMode(button2Pin, INPUT);
  pinMode(ledPin, OUTPUT);
}

void loop()
{
  int button1State, button2State;

  button1State = digitalRead(button1Pin);
  button2State = digitalRead(button2Pin);

  // XOR logic: on if either pressed, off if both pressed
  if (((button1State == LOW) || (button2State == LOW))
      && !
      ((button1State == LOW) && (button2State == LOW)))
  {
    digitalWrite(ledPin, HIGH);
  }
  else
  {
    digitalWrite(ledPin, LOW);
  }
}

Matériaux pour cette étape :

Arduino Uno R3Arduino Uno R31 pièce

Outils nécessaires :

Ordinateur avec l'IDE ArduinoOrdinateur avec l'IDE Arduino
4

Test & Experiment

What You Should See

The LED turns on when you press either button individually. It turns off when you press both buttons simultaneously (XOR logic).

Troubleshooting

  • Not responding: Push buttons are square — it's easy to put them in the wrong orientation. Try rotating 90°.
  • LED always on or always off: Check the pull-up resistor connections. Without them, the input pin floats and reads random values.

Experiments to Try

  • Change the logic to AND (both buttons required) or simple OR.
  • Use the buttons to control an RGB LED — one button for color, one for brightness.
  • Try using INPUT_PULLUP mode to eliminate the external resistors.

Matériaux

8

Outils requis

1
Total estimé
Ce que le maker a acheté. Les matériaux sans prix se trouvent là où vous les achetez.
€92.44

CC0 Domaine public

Ce blueprint est publié sous CC0. Vous êtes libre de copier, modifier, distribuer et utiliser ce travail pour tout usage, sans demander la permission.

Soutenez le Maker en achetant des produits via son Blueprint où il perçoit une Commission Maker définie par les Vendeurs, ou créez une nouvelle itération de ce Blueprint et incluez-le comme connexion dans votre propre Blueprint pour partager les revenus.

Commentaires

(0)

Se connecter pour participer à la discussion

Chargement des commentaires...