Collaboration
ART
BEAUTÉ ET BIEN-ÊTRE
ARTISANAT
CULTURE ET HISTOIRE
DIVERTISSEMENT
ENVIRONNEMENT
NOURRITURE ET BOISSONS
INGÉNIERIE INVERSE
SCIENCES
SPORTS
TECHNOLOGIE
TECHNOLOGIE PORTABLE
Soldering Iron: Temperature Controlled by a Curie-Point Tip and a Magnet Switch (Weller, US 3,188,448, 1965)
Ed

Créé par

Ed

3. novembre 2026FI
12
0
0
1
0

Soldering Iron: Temperature Controlled by a Curie-Point Tip and a Magnet Switch (Weller, US 3,188,448, 1965)

A soldering iron that holds its own tip temperature. At the back of the copper tip sits a slug of nickel-iron alloy that stops being magnetic above a set temperature (its Curie point). A small Alnico magnet behind it is pulled forward while the slug is cool, closing a switch that feeds the heater; once the tip is hot the slug lets go, a steel bushing pulls the magnet back and the switch opens. Swap tips to choose 600, 700 or 800 °F. Result: a 55-watt temperature-controlled iron idling near 700 °F instead of running ever hotter. Source: C. E. Weller, US 3,188,448 (1965). Unknown: the plating baths, the heater wire and insulation, most sizes. Picture: the patent drawing.
Avancé
Unknown

Consignes

1

Make the tip and control slug

Turn the tip from tellurium copper: a cylindrical body, a taper and a chisel end (any shape suits the work). Plate it first with iron, which keeps the copper out of the molten solder, then with nickel, which shuts out the air. Bore its rear end and fit tightly into it the shank of a slug of thermomagnetic nickel-iron alloy, such as 48 % nickel, 3 % molybdenum and the rest iron, or about 43 % nickel and the rest iron. The alloy sets the control point: make tips for 600, 700 and 800 °F. Not given: the plating baths, sizes.

Matériaux pour cette étape :

Barre de cuivre au tellureBarre de cuivre au tellure1 tip
Alliage fer-nickel thermomagnétiqueAlliage fer-nickel thermomagnétique1 control slug

Outils nécessaires :

Tour à métauxTour à métaux
Kit de galvanoplastieKit de galvanoplastie
Dimensions inconnuesDimensions inconnues
2

Wind the heater barrel

Make the barrel of two stainless steel tubes: an inner spool the tip slides into snugly, and an outer cover tube joined to it at the front, with a thread and screw cap to hold the tip. In the space between them wind the heater from one length of resistance wire: an inner layer, then an outer layer wound the opposite way so their fields cancel, with insulating sheet inside, between and outside the layers. Silver-solder heat-resistant leads to its ends. Ours: nichrome wire. Not given: the insulating sheet, the turns.

Matériaux pour cette étape :

Tube en acier inoxydableTube en acier inoxydable2 spool and cover tube
Fil de nichromeFil de nichrome1 heater
Isolant inconnuIsolant inconnu1 three sheet layers
Métal inconnuMétal inconnu1 leads
Brasure à l'argentBrasure à l'argent1 as needed

Outils nécessaires :

Chalumeau à propaneChalumeau à propane
Tour à métauxTour à métaux
3

Build the magnet switch

In a stainless steel sleeve about 2.4 in long, close the front with a non-magnetic thermal bushing. Behind it slides a cylindrical Alnico V magnet, then a non-magnetic spacer about 0.032 in thick, then a cold-drawn steel bushing about 0.50 in long held by dents in the sleeve; the magnet's stroke is about 0.015 in. A push rod runs from the magnet through the bushing to an insulator. On a melamine plate, hinge a moving contact between a thin conducting strip and a holding strip, facing a flexible contact; a spring of fourteen coils of 0.010 in music wire, 0.210 in across, presses the moving contact toward the flexible one. Rivet the spring bracket to the holding strip. Not given: the contact metals.

Matériaux pour cette étape :

Tube en acier inoxydableTube en acier inoxydable1 sleeve
Aimant AlnicoAimant Alnico1 pièce
Rond en acier douxRond en acier doux1 magnetic bushing, push rod
Métal inconnuMétal inconnu1 thermal bushing, spacer, contacts, strips, brackets
Matériau inconnuMatériau inconnu1 insulator
Plaque de mélaminePlaque de mélamine1 base plate
Fil d'acier à ressortFil d'acier à ressort1 0.010 in music wire spring

Outils nécessaires :

Tour à métauxTour à métaux
Jeu à riverJeu à river
Pince à becs rondsPince à becs ronds
4

Assemble the handle and use

Mould the handle in two plastic halves with a socket at the front whose bosses lock the cover tube. Lay in the switch unit, held only by the bowed tail of its holding strip on an anchor pin with a speed nut, so it floats and its thermal bushing presses on the tip's slug. Wire the heater, the switch and a ground lead from the cover tube to the cord. Rivet the halves near the butt and fit a split ring near the front. In use, below the control point the slug pulls the magnet forward and the spring closes the contacts; above it the steel bushing pulls the magnet back and the push rod opens them. At idle the heater runs only about 30 to 40 % of the time. Not given: the plastic.

Matériaux pour cette étape :

Matériau inconnuMatériau inconnu1 handle halves
Métal inconnuMétal inconnu1 rivet, split ring, speed nut
Cordon souple avec ficheCordon souple avec fiche1 pièce

Outils nécessaires :

Presse à injecterPresse à injecter
Jeu à riverJeu à river

Matériaux

13

Outils requis

7

CC0 Domaine public

Ce blueprint est publié sous CC0. Vous êtes libre de copier, modifier, distribuer et utiliser ce travail pour tout usage, sans demander la permission.

Soutenez le Maker en achetant des produits via son Blueprint où il perçoit une Commission Maker définie par les Vendeurs, ou créez une nouvelle itération de ce Blueprint et incluez-le comme connexion dans votre propre Blueprint pour partager les revenus.

Commentaires

(0)

Se connecter pour participer à la discussion

Chargement des commentaires...