Collaboration
ART
BEAUTÉ ET BIEN-ÊTRE
ARTISANAT
CULTURE ET HISTOIRE
DIVERTISSEMENT
ENVIRONNEMENT
NOURRITURE ET BOISSONS
INGÉNIERIE INVERSE
SCIENCES
SPORTS
TECHNOLOGIE
TECHNOLOGIE PORTABLE
Alcohol Burner: the Glass Spirit Lamp with a Copper Wick Shield (Morfit, 1849)
Charlie

Créé par

Charlie

7. novembre 2026DE
17
0
0
0
0

Alcohol Burner: the Glass Spirit Lamp with a Copper Wick Shield (Morfit, 1849)

A small glass lamp that burns alcohol for heating test tubes and small vessels on the bench. Campbell Morfit (1849): the glass body holds the alcohol; a round copper shield with a tube in its centre carries a cotton wick and rests on the neck; a minute hole in the shield lets vapour escape; a glass cap ground to fit the neck keeps the alcohol from evaporating. Alcohol gives no smoke and does not blacken the glass. Sizes, and how the wick tube is fixed, are not given. Source: C. Morfit, Chemical and Pharmaceutic Manipulations (1849), pp. 160-162. Picture: Fig. 115.
Débutant
Unknown

Consignes

1

Read Morfit

"To the neck b is adjusted a copper circular shield c, with a tube in its centre for the passage of the wick, which should be of cotton, and similar to that used for tallow candles. The shield should rest upon, rather than within the neck, otherwise its expansion by the heat may cause the breakage of the glass. A minute opening drilled in the shield is also requisite for the escape of vapor in case the alcohol should become heated."
2

Make the copper shield

Cut a round copper shield a little wider than the neck of the glass body, so it rests on the neck and not inside it. Fix a short copper tube through its centre for the wick (ours: soldered; the joint is not given). Drill a minute hole in the shield for vapour to escape. Sizes are not given (unknown).

Matériaux pour cette étape :

Feuille de cuivreFeuille de cuivre1 shield
Tube de cuivreTube de cuivre1 wick tube
Soudure étain-plombSoudure étain-plomb1 joint
FluxFlux1 joint

Outils nécessaires :

Cisaille à tôleCisaille à tôle
Fer à souderFer à souder
Chignole à mainChignole à main
Dimensions inconnuesDimensions inconnues
3

Fit the wick and the body

Draw a cotton wick of the tallow-candle kind through the tube so it reaches down into the glass body, which is the alcohol reservoir. Set the shield on the neck. Ours: a clear glass bottle as the body.

Matériaux pour cette étape :

Bouteille en verre (transparente)Bouteille en verre (transparente)1 body
Mèche de bougie en cotonMèche de bougie en coton1 pièce

Outils nécessaires :

Cisaille à tôleCisaille à tôle
4

Fit the glass cap

Cover the wick, when the lamp is not in use, with a glass cap ground inside to fit the neck closely. It stops the alcohol evaporating and the wick taking up water, which makes relighting difficult. Put it on only after the lamp is out. How the cap is made and ground is not given (unknown).

Matériaux pour cette étape :

Verre inconnuVerre inconnu1 cap

Outils nécessaires :

Dimensions inconnuesDimensions inconnues
5

Fill and use

Morfit burns alcohol of about specific gravity 0.85. Always put the lamp out before refilling, then pour the spirit in gently until the reservoir is nearly full. The flame is hottest just below its tip; bring the vessel to it gradually, and spread the heat with copper gauze between flame and vessel for larger surfaces.

Matériaux

7

Outils requis

4

CC0 Domaine public

Ce blueprint est publié sous CC0. Vous êtes libre de copier, modifier, distribuer et utiliser ce travail pour tout usage, sans demander la permission.

Soutenez le Maker en achetant des produits via son Blueprint où il perçoit une Commission Maker définie par les Vendeurs, ou créez une nouvelle itération de ce Blueprint et incluez-le comme connexion dans votre propre Blueprint pour partager les revenus.

Commentaires

(0)

Se connecter pour participer à la discussion

Chargement des commentaires...