ART
BEAUTÉ ET BIEN-ÊTRE
ARTISANAT
CULTURE ET HISTOIRE
DIVERTISSEMENT
ENVIRONNEMENT
NOURRITURE ET BOISSONS
INGÉNIERIE INVERSE
SCIENCES
SPORTS
TECHNOLOGIE
TECHNOLOGIE PORTABLE

The Economiser: The Heat Still Going Up the Chimney
Even a good boiler sends its flue gas up the chimney hot. Edward Green's economiser of 1845 put a bank of cast-iron tubes in the flue and ran the cold feed water through them on its way to the boiler, so the gas that was leaving anyway warmed the water that was arriving anyway. His tubes carried mechanical scrapers that travelled up and down them to keep the soot off, because a sooted tube is an insulated tube.
The same idea is in every modern condensing boiler, which cools its flue gas until the water vapour in it condenses and gives up its latent heat too.
This rung works out how much heat the stack carries away, measures a real flue, and finds the dew point below which an economiser starts to run wet.
Intermédiaire
About 3 hours
Consignes
1
1
Stack loss and the dew point
Stack loss and the dew point
Chargement du notebook Jupyter…
2
2
Measure a real flue
Measure a real flue
Find a flue you are allowed to measure: a wood stove's stove pipe, a workshop heater, the test port of a gas boiler (ask whoever services it). Strap the thermocouple tip against the flue pipe with a hose clip a metre above the appliance, and log it every minute from a cold start to steady running. Measure the room air too.
The pipe surface reads lower than the gas inside, so this is a floor under the true stack temperature. Put it into the notebook's table: even the floor usually shows several per cent of the fuel leaving as heat.
Never block, puncture or restrict a working flue. Flue gas contains carbon monoxide.
Matériaux pour cette étape :
Assortiment de colliers de serrage1 jeuOutils nécessaires :
Thermocouple avec afficheur
Thermomètre de cuisine
Chronomètre
Clé à molette
Gants de travail en cuir3
3
The feed water gets the heat, not the room
The feed water gets the heat, not the room
An economiser is a counterflow heat exchanger (rung 5 of this batch explains why counterflow): the coldest water meets the coolest gas at the chimney end, and the warmest water meets the hottest gas at the boiler end. That is how it cools the gas as far as it does.
It sits between the feed pump and the boiler, so it runs at boiler pressure; a check valve and a safety valve protect it. Green's tubes were cast iron, with scraper gear travelling up and down them to deal with the soot.
4
4
The flue runs hotter than it should: find out why
The flue runs hotter than it should: find out why
A rising stack temperature is fuel going up the chimney. The usual causes, in order.
Flow
Loading...
5
5
History and context
History and context
**Edward Green of Wakefield, 1845** — the fuel economiser, cast-iron vertical tubes in the flue with mechanical scrapers. It spread through the mills of northern England and the name stuck to the whole class of flue-gas feed-water heaters. No patent number is asserted here.
Its descendants are the economiser bank in every power-station boiler, the air preheater (rung 7 of this batch), and the condensing domestic boiler.
**Honest limits.** An economiser adds resistance to the flue, so a natural-draught chimney may need a fan. Cooled below the dew point it condenses, and with sulphur fuels the condensate is acid. And a sooted or scaled economiser saves nothing.
Matériaux
1- Espace réservé
Outils requis
5- Espace réservé
- Espace réservé
- Espace réservé
- Espace réservé
- Espace réservé
Blueprints liés
Ces blueprints partagent des connaissances — techniques, matériaux ou principes

The Fire-Tube Boiler: Surface, Not Fire, Makes Steam
par Martin
Mécanique
12
0
0
0
0
0

Rotative Beam Engine
par Martin
TECHNOLOGIE
40
0
0
0
1
0

The Steam Injector: Feeding a Boiler With Its Own Steam
par Martin
Mécanique
5
0
0
0
0
0

The Cooling Tower
par Peter
Mécanique des Fluides
40
0
0
0
1
0

Seebeck Thermocouple
par Ed
TECHNOLOGIE
35
0
0
0
0
0
CC0 Domaine public
Ce blueprint est publié sous CC0. Vous êtes libre de copier, modifier, distribuer et utiliser ce travail pour tout usage, sans demander la permission.
Soutenez le Maker en achetant des produits via son Blueprint où il perçoit une Commission Maker définie par les Vendeurs, ou créez une nouvelle itération de ce Blueprint et incluez-le comme connexion dans votre propre Blueprint pour partager les revenus.