Collaboration
ART
BEAUTÉ ET BIEN-ÊTRE
ARTISANAT
CULTURE ET HISTOIRE
DIVERTISSEMENT
ENVIRONNEMENT
NOURRITURE ET BOISSONS
INGÉNIERIE INVERSE
SCIENCES
SPORTS
TECHNOLOGIE
TECHNOLOGIE PORTABLE
Wheelbarrow: a Small Wooden Barrow (Cassell's, 1900)
Woody

Créé par

Woody

4. novembre 2026NO
11
0
0
0
0

Wheelbarrow: a Small Wooden Barrow (Cassell's, 1900)

A small wooden wheelbarrow: ash hales (handles) framed with oak cross-pieces, splayed legs, a red-deal bottom and sides with a curved front board bound in hoop iron, and a 1 ft wheel of eight oak spokes and four ash felloes on an ash or oak axle. Painted red inside and light green outside, lined in a lighter colour and black. Source: P. N. Hasluck, Cassell's Cyclopaedia of Mechanics (1900), p. 176. Picture: the book's Figs. 1-2.
Intermédiaire
Unknown

Consignes

1

Make the hales

Cut the two ash hales 3 ft 1 in long, 1 5/8 in deep by 1 1/2 in thick, the handles rising 3 3/4 in above the underside. Leave no more than 5/8 in on the faces of the hale tops; dress out 3/8 in on the face and 1/4 in underneath.

Matériaux pour cette étape :

Planche de frênePlanche de frêne1 hales 3 ft 1 in x 1 5/8 x 1 1/2 in

Outils nécessaires :

Scie égoïneScie égoïne
RabotRabot
VastringueVastringue
2

Frame with oak cross-pieces

Make the cross-pieces of oak, edges dressed off underneath. Let the hind piece's tenons, gauged 1/2 in thick, come through the hales 1 1/4 in to support the legs (Fig. 2). Pin the hales and cross-pieces tight with 3/16 in wood pins.

Matériaux pour cette étape :

Planche de chêne blancPlanche de chêne blanc1 pièce
Goujon en boisGoujon en bois1 3/16 in pins

Outils nécessaires :

Scie à dosseretScie à dosseret
Bédane à mortaiserBédane à mortaiser
TrusquinTrusquin
Vilebrequin et mècheVilebrequin et mèche
Fausse équerreFausse équerre
3

Fit the legs and stays

Put on legs 1 1/2 in square, splayed at the top, standing 1 ft below the hales to suit a 1 ft wheel, with no more than a 1/4 in shoulder. Fasten legs to hales with 3 in bolts, heads outside. Fit four stays: two under the hales and two under the hind cross-pieces.

Matériaux pour cette étape :

Planche de chêne blancPlanche de chêne blanc1 legs 1 1/2 in square, stays
Boulon de carrosserieBoulon de carrosserie4 3 in

Outils nécessaires :

Scie égoïneScie égoïne
Vilebrequin et mècheVilebrequin et mèche
Jeu de tournevisJeu de tournevis
4

Bottom and sides

Put in the bottom board of 1/2 in red deal, overhanging the front cross-piece 5/8 in; paint all joints. Fit the sides to the hales, the front leaning up to 3 3/4 in beyond square; sides 9 in deep by 5/8 in thick, reduced to 8 1/4 in at the hind ends, front ends edged. Run a 3/16 in or 1/4 in bead on the edge.

Matériaux pour cette étape :

Planche de pinPlanche de pin1 1/2 in bottom, 5/8 in sides
Peinture à l'huilePeinture à l'huile1 pièce

Outils nécessaires :

Scie égoïneScie égoïne
RabotRabot
Jeu de pinceauxJeu de pinceaux
5

Front board and ironwork

Fit the front board, of 3/4 in red deal or elm, on top of the hales and bottom board, rising in a curve 1 1/4 in above the sides. Paint the joints and nail the sides to it with 1 1/2 in cut nails; screw on the 7/8 in hoop iron with 3/4 in round-headed screws.

Matériaux pour cette étape :

Planche de pinPlanche de pin1 3/4 in front board
Clous en ferClous en fer1 1 1/2 in cut nails
Plat en acier douxPlat en acier doux1 7/8 in hoop iron
Vis à boisVis à bois1 3/4 in round-headed
Peinture à l'huilePeinture à l'huile1 pièce

Outils nécessaires :

Scie égoïneScie égoïne
MarteauMarteau
Jeu de tournevisJeu de tournevis
Jeu de pinceauxJeu de pinceaux
6

Make the wheel

Turn an ash or oak axle 8 1/4 in long by 2 1/2 in, its ends turned down to 1 1/2 in for ferrules 1 in long; drive 3/8 in round pins into the ends to stand out 1 in. Fit eight oak spokes 3/4 in by 1/2 in and four ash felloes 1 1/4 in square, joined with four 1/4 in dowels and bevelled to take a 3/4 in by 1/8 in hoop, rounded inside.

Matériaux pour cette étape :

Planche de frênePlanche de frêne1 axle and felloes
Planche de chêne blancPlanche de chêne blanc1 spokes
Tige de ferTige de fer1 3/8 in pins
Goujon en boisGoujon en bois4 1/4 in
Plat en acier douxPlat en acier doux1 3/4 x 1/8 in tyre

Outils nécessaires :

Tour à boisTour à bois
VastringueVastringue
Vilebrequin et mècheVilebrequin et mèche
MarteauMarteau
7

Hang the wheel and paint

Screw under each hale an iron 3/4 in broad by 1/8 in thick, long enough to pass the front cross-piece by 2 or 3 in, its eye taking the axle pin. Paint the wheel and the inside of the barrow red, the outside light green, lined in a lighter colour and black.

Matériaux pour cette étape :

Plat en acier douxPlat en acier doux2 3/4 x 1/8 in irons
Vis à boisVis à bois1 pièce
Peinture à l'huilePeinture à l'huile1 pièce

Outils nécessaires :

Jeu de tournevisJeu de tournevis
Jeu de pinceauxJeu de pinceaux

Matériaux

10

Outils requis

12

CC0 Domaine public

Ce blueprint est publié sous CC0. Vous êtes libre de copier, modifier, distribuer et utiliser ce travail pour tout usage, sans demander la permission.

Soutenez le Maker en achetant des produits via son Blueprint où il perçoit une Commission Maker définie par les Vendeurs, ou créez une nouvelle itération de ce Blueprint et incluez-le comme connexion dans votre propre Blueprint pour partager les revenus.

Commentaires

(0)

Se connecter pour participer à la discussion

Chargement des commentaires...