Collaboration
ART
BEAUTÉ ET BIEN-ÊTRE
ARTISANAT
CULTURE ET HISTOIRE
DIVERTISSEMENT
ENVIRONNEMENT
NOURRITURE ET BOISSONS
INGÉNIERIE INVERSE
SCIENCES
SPORTS
TECHNOLOGIE
TECHNOLOGIE PORTABLE
Shoe Horn With a Rolled Tubular Tang, Cut From One Sheet (Williams, 1901)
Forge

Créé par

Forge

13. novembre 2026NO
12
0
0
0
0

Shoe Horn With a Rolled Tubular Tang, Cut From One Sheet (Williams, 1901)

Alfred G. Williams of Newark received US 685,548, dated 29 October 1901, for a sheet-metal shoe horn whose handle tang is part of the same blank. A tongue at the narrow end is rolled into a close tube, and two wings beside it are folded over the edges of the horn, so the weak neck is stiffened where it meets the tang. A handle fits on the tang. We cut it from brass sheet with a 1:1 template and fit a hardwood handle. All sizes are ours.
Débutant
About 3 hours

Consignes

1

How wide to cut the tongue

Chargement du notebook Jupyter…
2

Read US 685,548

"I construct the tang by extending the sheet metal from the upper or smaller end of the horn in a tongue of suitable width to roll into a tubular tang and form integral with such tongue lateral wings or flanges upon the upper end of the horn, which can be folded or curved upon the edges of the horn to stiffen the same at its junction with the tang."
3

Print the template

The blank at 1:1 as his Fig. 1: body a, wings b, tongue c, with the fold lines a' dashed: they run from where each wing starts in to the root of the tongue. print at 100 % (check the 50 mm bar).
Fichier de designPDFCC0 - Free
4

Cut the blank

Cut the paper blank out and lay it on 0.8 mm brass sheet. Scribe round it. Cut just outside the line with tin snips, then file to the line. Keep the tongue an even 15 mm wide.

Matériaux pour cette étape :

Feuille de laitonFeuille de laiton1 pièce

Outils nécessaires :

Pointe à tracerPointe à tracer
Cisaille à tôleCisaille à tôle
Jeu de limesJeu de limes
Étau d'établiÉtau d'établi
5

Smooth the edges

Round every edge of the body with a file and sandpaper. The mouth slides against the heel and the sock, so it must be smooth all round.

Outils nécessaires :

Jeu de limesJeu de limes
Papier abrasifPapier abrasif
6

Roll the tang

Lay a 4 mm rod along the middle of the tongue. With round-nose pliers, curl one edge of the tongue up round the rod, then the other, a little at a time along its length, until the edges meet: his "close-rolled cylindrical" tang c'. Slide the rod out.

Outils nécessaires :

Pince à becs rondsPince à becs ronds
Pince platePince plate
Rond en acier douxRond en acier doux
7

Fold the wings

Fold each wing b along its dashed line a' over the edge of the horn, onto the underside, with the flat-nose pliers and then light taps of the rubber mallet, until it lies close. His Figs. 3 and 4 show the horn turned over, with the wings b' lying on the edges and running into the tang.

Outils nécessaires :

Pince platePince plate
Maillet en caoutchoucMaillet en caoutchouc
8

Dish the body

His body is "slightly concave transversely". Lay it, inside up, across a rod held in the vice and tap the edges down with the rubber mallet, working from the neck to the mouth, until it is evenly hollow across its width. Keep the curve slight; it should still lie nearly flat on the bench along its length.

Outils nécessaires :

Maillet en caoutchoucMaillet en caoutchouc
Barre ronde en acier douxBarre ronde en acier doux
Étau d'établiÉtau d'établi
9

Make the handle

Saw 75 mm of hardwood handle stock (ours) and shape it with a rasp and sandpaper. Drill a 6 mm hole 40 mm deep in one end, straight down the middle, to take the tang. His handle is "more for ornament than for support", so any shape you like will do.

Matériaux pour cette étape :

Barreau de bois dur pour manchesBarreau de bois dur pour manches1 pièce

Outils nécessaires :

Scie à métauxScie à métaux
Râpe à boisRâpe à bois
Papier abrasifPapier abrasif
Chignole à mainChignole à main
Étau d'établiÉtau d'établi
10

Fit the handle

Roughen the tang with sandpaper, mix the epoxy, fill the hole and push the handle onto the tang until it meets the wings. Line the handle up with the horn and leave it to set as the epoxy's label says.

Matériaux pour cette étape :

Époxy à deux composantsÉpoxy à deux composants1 pièce

Outils nécessaires :

Papier abrasifPapier abrasif
11

Polish

Polish the horn with polishing compound on a soft cloth.

Outils nécessaires :

Pâte à polirPâte à polir
12

Troubleshooting

Tubular-tang shoe horn troubleshooting.

Flow

Loading...
13

History and honest limits

**Alfred G. Williams** of Newark, New Jersey, assignor to Havell Manufacturing Company, US 685,548, dated 29 October 1901, filed 26 June 1901. He claimed "the shoe-horn having integral tang c', of close-rolled cylindrical form, with integral wings b' extended from such tang and folded over upon the edges of the horn". He meant it for "ornamented handles" in "mounted toilet sets". He gives no sizes, no metal and no way of fixing the handle: the brass, all sizes, the hardwood handle, the epoxy and the order of work are ours.

Matériaux

3

Outils requis

14

Fichiers de conception

1

CC0 Domaine public

Ce blueprint est publié sous CC0. Vous êtes libre de copier, modifier, distribuer et utiliser ce travail pour tout usage, sans demander la permission.

Soutenez le Maker en achetant des produits via son Blueprint où il perçoit une Commission Maker définie par les Vendeurs, ou créez une nouvelle itération de ce Blueprint et incluez-le comme connexion dans votre propre Blueprint pour partager les revenus.

Commentaires

(0)

Se connecter pour participer à la discussion

Chargement des commentaires...