Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Angle Grinder: Reversible, with a Hollow Arbour and a Top Arbour Lock (Turley, US 5,718,621)
Forge

Dibuat oleh

Forge

9. November 2026NO
7
0
0
0
0

Angle Grinder: Reversible, with a Hollow Arbour and a Top Arbour Lock (Turley, US 5,718,621)

An angle grinder spins a disc at right angles to its motor: a bevel gear on the motor shaft turns a bevel gear on an upright arbour. E. M. Turley (US 5,718,621, 1998) makes the arbour hollow. A bolt runs down through it into a hexagonal coupling piece that drives the disc and clamps it against the arbour's flange, so the motor can run either way without loosening the disc. To change the disc, a sliding lock piece on top locks the arbour, opens a hole over the bolt head and switches the motor off in one move. Source: E. M. Turley, "Reversible Angle Grinder with Top Arbour Lock", US Patent 5,718,621 (filed 1996, granted 1998). Picture: its Fig. 1.
Lanjutan
Unknown

Instruksi

1

Read Turley

"The angle grinder according to the preferred embodiment of the invention includes a reversible motor driving a hollow arbour via a right angle bevel gear arrangement. The arbour has a right angle flange at its bottom. The flange abuts against one side of the disk tool."
2

Turn the hollow arbour

Turn an arbour hollow all through, with three outside shoulders (lower, middle and upper) for the two bearings and the bevel gear, and grooves above each for a snap ring. At the bottom, enlarge the bore into a hexagonal recess ending in a right-angle flange. At the top, enlarge the bore so the bolt head sits below the rim, and cut four equally spaced square notches (crenellations) in the rim. Sizes and metal are not given.

Material untuk langkah ini:

Logam tidak diketahuiLogam tidak diketahui1 arbour

Alat yang dibutuhkan:

Mesin Bubut LogamMesin Bubut Logam
Mesin FraisMesin Frais
Kikir (Kikir Tangan)Kikir (Kikir Tangan)
Dimensi tidak diketahuiDimensi tidak diketahui
3

Make the coupling piece and bolt

Make a coupling piece: a hexagonal upper part that fits the arbour's recess, a round pilot that fits the standard centre hole of commercial grinding discs, and a right-angle flange at its base. Bore and tap it from the top, closed at the bottom. Make a retaining bolt long enough to run from the arbour's top down into the coupling piece, threaded at its lower end (Fig. 1 draws a socket in its head).

Material untuk langkah ini:

Logam tidak diketahuiLogam tidak diketahui1 coupling piece
Logam tidak diketahuiLogam tidak diketahui1 retaining bolt

Alat yang dibutuhkan:

Mesin Bubut LogamMesin Bubut Logam
Mesin FraisMesin Frais
Set pembuat ulirSet pembuat ulir
Dimensi tidak diketahuiDimensi tidak diketahui
4

Cut the bevel gears

Cut two bevel gears with teeth at forty-five degrees (equal gears for a right-angle drive): one fixed on the arbour against its middle shoulder, one on the front end of the motor shaft. Tooth count and metal are not given.

Material untuk langkah ini:

Logam tidak diketahuiLogam tidak diketahui2 bevel gears

Alat yang dibutuhkan:

Mesin FraisMesin Frais
Pisau frais roda gigi payungPisau frais roda gigi payung
Dimensi tidak diketahuiDimensi tidak diketahui
5

Assemble the drive

Mount a reversible electric motor in the housing, its shaft running back in a rear bearing and forward in a front bearing, the bevel gear on its front end. Set the arbour upright in two bearings at its lower and upper shoulders, the bevel gears meshing, with snap rings above the bearings and the gear. Drop the bolt down the arbour on a lock washer, fit the coupling piece from below and screw it on. Motor rating, housing material and how the bearings are held are not given.

Material untuk langkah ini:

Motor listrikMotor listrik1 reversible
Bantalan PeluruBantalan Peluru4 buah
Bahan tidak diketahuiBahan tidak diketahui1 housing

Alat yang dibutuhkan:

Set kunci LSet kunci L
Metode pembentukan tak diketahuiMetode pembentukan tak diketahui
Dimensi tidak diketahuiDimensi tidak diketahui
6

Fit the arbour lock

Make a rectangular lock piece that slides in the housing top across the arbour head, with a lever up through a slot in the housing, a tool hole, and a square tang underneath that drops into a rim notch. A spring on its front face holds it back in the running position. Fix a two-contact power switch to its rear so the motor circuit is broken when the piece is slid into the locking position. Cut a hole in the housing top over the bolt head and a slot for the lever.

Material untuk langkah ini:

Logam tidak diketahuiLogam tidak diketahui1 lock piece
PegasPegas1 buah
Sakelar hidup/matiSakelar hidup/mati1 buah

Alat yang dibutuhkan:

Mesin FraisMesin Frais
Mesin Bor DudukMesin Bor Duduk
Set Mata BorSet Mata Bor
Kikir (Kikir Tangan)Kikir (Kikir Tangan)
7

Change a disc

Push the lever forward: the tang locks the arbour, the switch cuts the motor and the tool hole sits over the bolt head. Unscrew the bolt from above with the key and pull the coupling piece; put the new disc on its pilot and screw it back up tight, so the disc is clamped between the arbour flange and the coupling flange. Let the lever spring back to run. Turley: a loose bolt cannot drop the disc, which rattles to warn you to tighten it.

Alat yang dibutuhkan:

Set kunci LSet kunci L

Bahan

6

Alat yang Diperlukan

10

Cetak biru ini membuat

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...