Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Belt Sander: a Lathe-Driven Garnet-Belt Sander (Shop Notes, 1919)
Woody

Dibuat oleh

Woody

4. November 2026NO
11
0
0
0
0

Belt Sander: a Lathe-Driven Garnet-Belt Sander (Shop Notes, 1919)

A shop belt sander for dressing wood surfaces: a 6 in garnet-paper belt running over four crowned wooden pulleys, one driven by the lathe, pressed down onto the work with a hand float. Best belt speed about 2,500 ft per minute; leave about 1 in between work and belt. Source: Popular Mechanics Shop Notes for 1919, p. 3235. Picture: the article's drawing.
Menengah
Unknown

Instruksi

1

Turn the pulleys

Build up four solid wood pulleys 10 in across with 8 in faces and turn them in the lathe with a very slight crown; too much crown harms the belt.

Material untuk langkah ini:

Papan Kayu KerasPapan Kayu Keras4 built-up pulleys

Alat yang dibutuhkan:

Mesin bubut kayuMesin bubut kayu
2

Mount the pulleys

Mount one pulley on a firmly held arbor in the lathe and the other three on iron-pipe shafts on a frame (drawing). Turn and file a true journal on each pipe, pour babbitt bushings in the pulleys, and cut oil grooves in the pipe or babbitt. Supporting the shafts on one side lets the belt slip off; supporting both sides is stronger.

Material untuk langkah ini:

Pipa baja (berdinding tebal, ujung berulir)Pipa baja (berdinding tebal, ujung berulir)3 shafts
Logam tidak diketahuiLogam tidak diketahui1 babbitt bushings
Kayu pinusKayu pinus1 frame

Alat yang dibutuhkan:

Kikir LogamKikir Logam
Serok berlubangSerok berlubang
Gergaji TanganGergaji Tangan
PaluPalu
3

Make the belt

Cut 6 in garnet paper (No. 1 1/2 for general work) so the ends just meet over the pulleys. Glue the smooth side at the joint, splice it with a strip of cloth about 1 in wide and then one about 3 in wide, cover each side with paper, and clamp between two small boards.

Material untuk langkah ini:

AmplasAmplas1 6 in garnet paper
Kain KatunKain Katun1 buah
Lem hewaniLem hewani1 buah

Alat yang dibutuhkan:

Klem CKlem C
4

Set up and run

Run the belt at about 2,500 ft per minute using the lathe's cone pulley. Set the work about 1 in below the belt on a table or a low sliding platform (two sets of tongue-and-groove joints at right angles), start the machine and press the belt down with a float like a blackboard eraser, or a roller.

Material untuk langkah ini:

Kayu pinusKayu pinus1 platform, float

Alat yang dibutuhkan:

Mesin bubut kayuMesin bubut kayu

Bahan

7

Alat yang Diperlukan

6

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...