Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Bench Power Supply: Regulated, with Adjustable Current Limit and a Pentode Pass Tube (Gately, Forbro, US 3,243,690, 1966)
Ed

Dibuat oleh

Ed

3. November 2026FI
12
0
0
0
0

Bench Power Supply: Regulated, with Adjustable Current Limit and a Pentode Pass Tube (Gately, Forbro, US 3,243,690, 1966)

An adjustable bench supply that holds its output voltage steady and lets you set the most current it will deliver, so a circuit under test cannot be damaged. A pentode tube in series with the output is the regulator; a bridge with Zener references and a five-transistor amplifier keeps the output equal to the setting of one knob. A meter switch reads volts, amps, and the current limit, which can be set without disturbing the voltage. Result: a regulated DC bench supply with adjustable current limiting. Source: J. R. Gately (Forbro Design), US 3,243,690 (1966). Unknown: all component values and the output rating. Picture: the patent drawing.
Lanjutan
Unknown

Instruksi

1

Wire the mains side

In a case, wire the power cord through a switch and a fuse to the primary of a transformer with four secondaries, and put a neon lamp across the primary to show the supply is on. One secondary (6.3 V) goes to two terminals for outside use, one heats the pentode, one is the main supply and one the bias supply. Ours: the case. Not given: the other winding voltages.

Material untuk langkah ini:

Kotak pelindung aluminiumKotak pelindung aluminium1 case
Kabel lentur berstekerKabel lentur bersteker1 buah
Sakelar tuasSakelar tuas1 buah
SekringSekring1 buah
Trafo Penurun TeganganTrafo Penurun Tegangan1 four secondaries
Lampu indikator neonLampu indikator neon1 buah
Terminal panelTerminal panel2 6.3 V terminals

Alat yang dibutuhkan:

Bor tanganBor tangan
Set obengSet obeng
2

Build the rectifiers

Rectify the centre-tapped main winding with two rectifiers and smooth it with a capacitor. From the bias winding make two more supplies: one through two rectifiers with by-pass capacitors to a smoothing capacitor, for the pentode's screen and the reference circuit; the other through one rectifier and a capacitor, for the pentode's grid bias. Not given: the values.

Material untuk langkah ini:

DiodaDioda5 rectifiers
Kapasitor elektrolitKapasitor elektrolit3 smoothing
Set KapasitorSet Kapasitor1 by-pass
Kawat Timah SolderKawat Timah Solder1 as needed

Alat yang dibutuhkan:

SolderSolder
3

Fit the pass tube and reference

Put the pentode in series with the positive output: plate to the main supply, cathode through two current-sensing resistors (one fixed, one adjustable) to the + output terminal; suppressor tied to the cathode, screen fed through a resistor. Build the reference: a Zener fed through a resistor feeds a second Zener at constant current, giving a fixed voltage. Against it set two resistors and the voltage-control variable resistor: the output voltage is proportional to that resistor's setting. Not given: the tube type and values.

Material untuk langkah ini:

Tabung pentodeTabung pentode1 series pass tube
Dioda ZenerDioda Zener2 buah
HambatanHambatan1 set
ReostatReostat2 voltage control, current-limit range
Terminal panelTerminal panel2 output + and -
Kawat Timah SolderKawat Timah Solder1 as needed

Alat yang dibutuhkan:

SolderSolder
4

Build the error amplifier and current limit

Build a five-transistor amplifier that drives the pentode's grid to keep the bridge balanced: a PNP emitter follower, an NPN stage, a PNP emitter follower with a resistor-capacitor roll-off against oscillation, a PNP driver whose base resistor has a capacitor across it for quick response, and an NPN clamp whose base is set by a potentiometer. Feed the voltage across the current-sensing resistors to the driver's base through a diode: above the limit it takes over and turns the pentode down. Choose the fixed sensing resistor to limit at about 125 % of rated current, trim with the potentiometer, and use the adjustable one to set lower limits. Not given: the transistor types and values.

Material untuk langkah ini:

Transistor PNPTransistor PNP3 buah
Transistor NPNTransistor NPN2 buah
DiodaDioda1 buah
PotensiometerPotensiometer1 buah
Set KapasitorSet Kapasitor1 roll-off, speed-up
HambatanHambatan1 set
Kawat Timah SolderKawat Timah Solder1 as needed

Alat yang dibutuhkan:

SolderSolder
5

Fit the meter and use it

Fit a meter with a four-pole, three-position switch. Position 1 reads output volts through a multiplier resistor; position 2 reads current across a shunt in the negative line; position 3 (spring-return) puts a load resistor across the output and swaps a fixed resistor for the voltage control, so you can turn the limit control until the current limits at the value you want, without touching the voltage setting. Release the switch and use the supply.

Material untuk langkah ini:

Meter panel kumparan putarMeter panel kumparan putar1 buah
Sakelar putarSakelar putar1 4-pole, 3-position
HambatanHambatan1 multiplier, shunt, load resistors
Bahan tidak diketahuiBahan tidak diketahui1 terminal strip

Alat yang dibutuhkan:

SolderSolder
Set obengSet obeng

Bahan

21

Alat yang Diperlukan

3
  • Placeholder
  • Placeholder
  • 2 vendors sell this, none ship to you yet
    Placeholder

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...