Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI

Ski Staff: Bamboo Pole With Wrist Loop, Wooden Snow Disk and Lead-Set Spike (Boy Mechanic, 1915)
A homemade ski staff from The Boy Mechanic, Book 2 (1915): a 4-1/2 ft bamboo pole with a leather wrist loop at the top, a 5 in pine disk 6 in above the tip to stop it sinking in deep snow, and a wire spike set in lead in a hardwood plug for icy ground.
Pemula
About 3 hours
Instruksi
1
1
His sizes in centimetres
His sizes in centimetres
Memuat notebook Jupyter…
2
2
Read The Boy Mechanic, Book 2
Read The Boy Mechanic, Book 2
"A ski staff will greatly assist progress over level stretches and is an aid to the ski runner in preserving his balance."
3
3
Cut the staff and loop
Cut the staff and loop
Cut a bamboo pole 1-1/4 or 1-1/2 in in diameter and 4-1/2 ft long. Shave an old strap thinner, cut it about 1/2 in wide, and fix it as a narrow wrist loop at the top.
Material untuk langkah ini:
Bilah bambu panjang1 buah
Kulit pelana dan tali kuda1 buah
Paku keling tembaga1 buahAlat yang dibutuhkan:
Gergaji Tangan
Pisau kulit
Bor tangan
Palu
Meteran Gulung4
4
Make and fix the snow disk
Make and fix the snow disk
Cut a disk of well-seasoned white pine or spruce, 1/2 in thick and 5 in in diameter, and coat it with shellac. Bore its centre to pass up the staff about 6 in. Fix it with two pieces of heavy wire: wire A goes through the staff below wire B and at right angles to it, so B must be bent over A. Staple both wires to the disk.
Material untuk langkah ini:
Papan pinus1 buah
Pernis sirlak1 buah
Kawat besi1 buah
Paku U kawat4 buahAlat yang dibutuhkan:
Gergaji Coping
Bor engkol dan mata bor
Bor tangan
Tang Berujung Rata
Palu
Kuas lebar5
5
Set the spike
Set the spike
Plug the lower end with hard wood and bore part way into its centre for a wire spike. Cut slight recesses in the sides of the hole to anchor lead, and pour melted lead round the spike. Sharpen the point, then wind the bamboo with waxed twine or fine wire so it does not split.
Material untuk langkah ini:
Papan Kayu Keras1 buah
Kawat besi1 buah
Batangan Timbal1 buah
Tali goni1 buah
Malam Lebah1 buahAlat yang dibutuhkan:
Bor tangan
Pahat kayu
Gayung logam
Obor Propana
Kikir (Kikir Tangan)
Tang Berujung Rata6
6
Troubleshooting
Troubleshooting
Ski staff troubleshooting.
Flow
Loading...
7
7
History and honest limits
History and honest limits
From "How to Make a Ski Staff", in **The Boy Mechanic, Book 2**, Popular Mechanics, 1915 (Project Gutenberg 44585; checked on the archive.org scan boymechanicbook200chic2, p. 51). No contributor is named. He gives no wire gauge or spike length. The tools and metric figures are ours.
Bahan
11- 1 buahPlaceholder
- Placeholder
- 1 buahPlaceholder
- 1 buahPlaceholder
- 1 buahPlaceholder
- 2 buahPlaceholder
- 4 buahPlaceholder
- 1 buahPlaceholder
- 1 buahPlaceholder
- 1 buahPlaceholder
- 1 buahPlaceholder
Alat yang Diperlukan
13- Placeholder
- Placeholder
- Placeholder
- Placeholder
- 1 vendor sell this, none ship to you yetPlaceholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
Cetak biru ini membuat
Blueprint terkait
Blueprint ini berbagi pengetahuan — teknik, bahan, atau prinsip
CC0 Domain Publik
Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.
Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

