Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Four-Passenger Coasting Bobsled: Iron-Shod Ash Runners, Hinged Rear Sled and Hoop Steering Wheel (Boy Mechanic, 1915)
Woody

Dibuat oleh

Woody

13. November 2026NO
6
0
0
0
0

Four-Passenger Coasting Bobsled: Iron-Shod Ash Runners, Hinged Rear Sled and Hoop Steering Wheel (Boy Mechanic, 1915)

R. H. Allen's four-passenger coasting bob from The Boy Mechanic, Book 2 (1915): a 6-1/2 ft top board with four hinged seat backs, carried on two short sleds with ash runners shod in 5/8 in round iron. The rear sled rocks on a wedge and hinges to follow the ground; the front sled steers by a broom-handle post and a wheel made from a nail-keg hoop. Every size is his.
Menengah
About 3 days

Instruksi

1

His list of materials in centimetres

Memuat notebook Jupyter…
2

Read The Boy Mechanic, Book 2

"Any wood may be used for the sled, except for the runners, which should be made of ash." His list of materials: 1 top 6-1/2 ft x 16 in x 1-1/4 in; 4 runners 22 x 4 x 1 in; 4 crosspieces 16 x 3 x 1 in; 3 pieces 16 x 5 x 2 in; 1 piece 16 x 5 x 1 in; 1 shore 16 x 3 x 1 in; 4 seat backs 12 x 16 x 1 in; 1 dowel 3 ft x 1 in; 4 rods 5/8 in x 30 in; 4 eyebolts 1/2 x 6 in; 3 hinges 5 in strap; 8 hinges 3 in strap.
3

Shape and shoe the runners

Cut one ash runner to shape and use it as the pattern for the other three. Cut a groove about 1/4 in deep along the under edge to take the curve of a 5/8 in round iron rod. Bend each rod to fit in the groove, up the back of the runner and over the top at the front; flatten the ends and drill two holes in each for wood screws (a blacksmith can flatten them, he says). Screw the irons on.

Material untuk langkah ini:

Papan Kayu KerasPapan Kayu Keras1 buah
Batang besi bulatBatang besi bulat4 buah
Sekrup kayuSekrup kayu1 buah

Alat yang dibutuhkan:

Gergaji TanganGergaji Tangan
Gergaji CopingGergaji Coping
Pahat kayuPahat kayu
Perapian tempa berbahan bakar batu baraPerapian tempa berbahan bakar batu bara
Landasan TempaLandasan Tempa
Palu pandai besiPalu pandai besi
Ragum MejaRagum Meja
Bor tanganBor tangan
PensilPensil
4

Build the two sleds

Notch the top edges of each pair of runners for the 16 x 3 in crosspieces, near the ends, so the crosspieces lie flush with the runner tops and the notches of each pair line up. Fit them snugly, fasten with long, slim wood screws, and stiffen each joint inside with a small metal brace.

Material untuk langkah ini:

Papan pinusPapan pinus1 buah
Sekrup kayuSekrup kayu1 buah
Siku penguat sudutSiku penguat sudut8 buah

Alat yang dibutuhkan:

Gergaji TanganGergaji Tangan
Pahat kayuPahat kayu
Bor tanganBor tangan
5

Make the rocking rear joint

Cut a heavy 2 x 5 in crosspiece sloping across its width, from 2 in thick at one edge to a feather edge at the other. Fix the three large strap hinges to the sloping face, and fasten the piece solidly on the rear sled's runners with its centre 8 in from their front ends. This lets the rear sled rock but not turn sideways.

Material untuk langkah ini:

Papan pinusPapan pinus1 buah
Engsel tali besiEngsel tali besi3 buah
Sekrup kayuSekrup kayu1 buah

Alat yang dibutuhkan:

Gergaji TanganGergaji Tangan
Ketam tanganKetam tangan
Bor tanganBor tangan
6

Mount the front sled crosspiece

Fasten the supporting crosspiece on top of the front sled's runners with its centre 11 in from their front ends.

Material untuk langkah ini:

Papan pinusPapan pinus1 buah
Sekrup kayuSekrup kayu1 buah

Alat yang dibutuhkan:

Bor tanganBor tangan
Meteran GulungMeteran Gulung
7

Brace the top board

Round both ends of the top board and plane it smooth. Underneath, fit two crosspieces, each with two 1/2 in holes bored through its width near the ends for the eyebolts: one with its centre 12 in from the rear end, the other 8 in from the front. Screw them on. Set the shore in the centre of the board, run wires over it between the eyebolts, and draw the eyebolts up until the wire is taut over the shore, so the long board cannot sag.

Material untuk langkah ini:

Papan pinusPapan pinus1 buah
Baut mataBaut mata4 buah
Kawat besiKawat besi1 buah
Sekrup kayuSekrup kayu1 buah

Alat yang dibutuhkan:

Gergaji TanganGergaji Tangan
Ketam tanganKetam tangan
Bor engkol dan mata borBor engkol dan mata bor
Meteran GulungMeteran Gulung
8

Fit the seat backs and foot rests

Round the top corners of the four backs and cut the bottom ends at a slight angle for a slant. Hinge them to the top board with the small strap hinges every 18 in, starting at the rear. Bore 1 in holes about 1 in deep in the edges of the top board every 18 in, beginning about 5 in from the front, and drive in pins 4 in long cut from the dowel, as foot rests.

Material untuk langkah ini:

Papan pinusPapan pinus1 buah
Engsel tali besiEngsel tali besi8 buah
Pasak kayu kerasPasak kayu keras1 buah
Sekrup kayuSekrup kayu1 buah

Alat yang dibutuhkan:

Gergaji TanganGergaji Tangan
Bor engkol dan mata borBor engkol dan mata bor
Meteran GulungMeteran Gulung
9

Make the steering

Cut a broom handle to 18 in and fasten one end in a hole bored centrally in the 5 in crosspiece of the front sled. Bore a hole in the top board through the centre of the crosspiece underneath; put two metal washers on the stick and run it up through the hole, then fasten a hardwood collar to it just above the board so the top cannot lift off the sled. For the wheel, fasten a piece of wood across a nail-keg hoop, cover the hoop with garden hose and wrap it with twine; bore the centre of the crosspiece to fit the broom handle and screw it on.

Material untuk langkah ini:

SapuSapu1 buah
Ring RataRing Rata2 buah
Papan Kayu KerasPapan Kayu Keras1 buah
Simpai besiSimpai besi1 buah
Selang karet berlapis kainSelang karet berlapis kain1 buah
Tali goniTali goni1 buah
Sekrup kayuSekrup kayu1 buah

Alat yang dibutuhkan:

Gergaji TanganGergaji Tangan
Bor engkol dan mata borBor engkol dan mata bor
Bor tanganBor tangan
10

Join the sleds and fit the ropes

Fasten the rear sled to the top board with screws through the free wings of the hinges into the crosspiece. Bore holes in the front ends of all runners and attach a chain or rope: the rear one's loop to the underside of the top board, the front one for drawing the sled.

Material untuk langkah ini:

Sekrup kayuSekrup kayu1 buah
Rantai besiRantai besi1 buah

Alat yang dibutuhkan:

Bor engkol dan mata borBor engkol dan mata bor
Bor tanganBor tangan
11

Troubleshooting

Bobsled troubleshooting.

Flow

Loading...
12

History and honest limits

From "Four-Passenger Coasting Bobsled" by R. H. Allen, in **The Boy Mechanic, Book 2**, Popular Mechanics, 1915 (Project Gutenberg 44585; checked on the archive.org scan boymechanicbook200chic2, pp. 24-26). The runner shape comes from his drawing, not from figures. The scan calls the steering collar a hardwood collar; the Gutenberg text drops "hardwood". The tools and metric figures are ours.

Bahan

15

Alat yang Diperlukan

12

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...