Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Homemade Wood Lathe: Hardwood Bed, Sliding Headstock and Tailstock, Steel Spindle With Stepped Pulley (Boy Mechanic, 1915)
Woody

Dibuat oleh

Woody

13. November 2026NO
10
0
0
0
0

Homemade Wood Lathe: Hardwood Bed, Sliding Headstock and Tailstock, Steel Spindle With Stepped Pulley (Boy Mechanic, 1915)

E. E. Hulgan's lathe from The Boy Mechanic, Book 2 (1915), "in which wood and light metal articles may be turned": a 5 ft bed of two 2 by 4 in hardwood rails, a headstock clamped by bolts with a 3/4 in steel spindle in brass bearings and a three-step pulley, a bolted hardwood tailstock with a screw-fed dead centre, a sliding tool rest, and a screw-on chuck. Driven from a countershaft or by foot.
Lanjutan
About 1-2 weeks

Instruksi

1

His sizes, and the pulley speeds

Memuat notebook Jupyter…
2

Read The Boy Mechanic, Book 2

"A strong, substantial lathe in which wood and light metal articles may be turned can be made by carefully following the description below and the detailed drawings of the parts."
3

Make the bed

Cut two pieces of straight-grained, smooth 2 by 4 in hardwood, 5 ft long, and hold them apart at each end with blocks of wood 2 in wide (Fig. 9 shows 2 in rails with a 2 in gap). The bed can be longer or shorter.

Material untuk langkah ini:

Papan Kayu KerasPapan Kayu Keras2 buah
Sekrup kayuSekrup kayu1 buah

Alat yang dibutuhkan:

Gergaji TanganGergaji Tangan
Ketam tanganKetam tangan
Bor tanganBor tangan
Meteran GulungMeteran Gulung
4

Build the headstock frame

Make the two hardwood end pieces to the shape of Figs. 1 and 2 (2 in thick, 2 in apart on an 8 in base, 7-1/2 in high, 6 in wide at the bottom) and screw them to the base. Nail a slider 1 in thick and 10 in long, just wide enough to slide between the bed rails, under the base, 2 in from its rear end. Bore two 1/2 in holes through base and slider and put two 1/2 in bolts through them and through another slide and board under the bed, so tightening the nuts clamps the headstock. Screw a half-round wedge-shaped brace inside the frame against the front end.

Material untuk langkah ini:

Papan Kayu KerasPapan Kayu Keras1 buah
Baut kepala bulat leher persegiBaut kepala bulat leher persegi2 buah
Mur Segi EnamMur Segi Enam2 buah
Sekrup kayuSekrup kayu1 buah
PakuPaku1 buah

Alat yang dibutuhkan:

Gergaji TanganGergaji Tangan
Pahat kayuPahat kayu
Bor engkol dan mata borBor engkol dan mata bor
Bor tanganBor tangan
5

Make the spindle and bearings

Make the spindle of tool steel or steel tubing, 3/4 in in diameter and 14 in long, and cut a thread on one end. Rivet on a hardened steel collar, 1/4 by 1-1/2 in, to turn against another collar of the same size on the headstock; screw a third collar to the rear end piece and fix a collar with a removable pin on the spindle, fitted to turn easily with no end play. Drill brass tubing for the spindle as bearings and wedge them into the headstock 6 in above the bed, in line; drill small oil holes from the top.

Material untuk langkah ini:

Batang baja perkakasBatang baja perkakas1 buah
Pipa baja bulatPipa baja bulat1 buah
Shaft CollarShaft Collar4 buah
Paku keling bajaPaku keling baja1 buah
Tabung kuninganTabung kuningan1 buah

Alat yang dibutuhkan:

Gergaji BesiGergaji Besi
Set pembuat ulirSet pembuat ulir
Bor tanganBor tangan
Kikir (Kikir Tangan)Kikir (Kikir Tangan)
Ragum MejaRagum Meja
PaluPalu
6

Fit the stepped pulley

Make the pulleys 2 in wide, with the diameters on the drawing: 6, 4-1/2 and 3 in. Fasten them to the spindle with a removable pin. (Turned hardwood is our choice of material; he does not say.)

Material untuk langkah ini:

Papan Kayu KerasPapan Kayu Keras1 buah

Alat yang dibutuhkan:

Gergaji TanganGergaji Tangan
Bor engkol dan mata borBor engkol dan mata bor
Bor tanganBor tangan
7

Make the chuck and centres

For the chuck (Fig. 3), take shafting 1-1/2 in in diameter and 2-1/2 in long, drill a 1/2 in hole through its centre, ream and thread one end to fit the spindle, and fit a setscrew over the 1/2 in hole. Make a wood-turning centre, and other centres and drills, from 1/2 in tool steel.

Material untuk langkah ini:

Batang bulat baja lunakBatang bulat baja lunak1 buah
Batang baja perkakasBatang baja perkakas1 buah
Baut tanam ujung cekungBaut tanam ujung cekung1 buah

Alat yang dibutuhkan:

Gergaji BesiGergaji Besi
Bor tanganBor tangan
Peluas lubangPeluas lubang
Set pembuat ulirSet pembuat ulir
Kikir (Kikir Tangan)Kikir (Kikir Tangan)
Ragum MejaRagum Meja
8

Build the tailstock

Build the tailstock (Figs. 4-6) of three pieces of hardwood 2 in thick and one 1 in thick, shaped as drawn, held together with four bolts 7-1/2 in long. Give it sliders and clamp it to the bed like the headstock, but with one bolt, and weld a handle to its nut for easy clamping. Drill a piece of tubing 2 in long for a 1/2 in dead centre and set it 1-1/2 in into the joint between the two upper pieces. Bore for a 1/2 in bolt to slide in the tube; chisel a recess behind the tube for a 1/2 in nut; turn a bolt 7 in long, threaded for 2 in, into nut and tube, and rivet a handle or wheel on its end. Make the centre of 1/2 in tool steel with a tapered point.

Material untuk langkah ini:

Papan Kayu KerasPapan Kayu Keras2 buah
Baut kepala bulat leher persegiBaut kepala bulat leher persegi5 buah
Mur Segi EnamMur Segi Enam2 buah
Pipa baja bulatPipa baja bulat1 buah
Batang baja perkakasBatang baja perkakas1 buah
Paku keling bajaPaku keling baja1 buah

Alat yang dibutuhkan:

Gergaji TanganGergaji Tangan
Pahat kayuPahat kayu
Bor engkol dan mata borBor engkol dan mata bor
Bor tanganBor tangan
Perapian tempa berbahan bakar batu baraPerapian tempa berbahan bakar batu bara
Landasan TempaLandasan Tempa
Palu pandai besiPalu pandai besi
Kikir (Kikir Tangan)Kikir (Kikir Tangan)
9

Make the tool rest

The tool rest (Figs. 7-9) has a slide 3/4 by 3 by 13 in with a slot 1/2 by 6 in. Bolt the rest base on the slide so it can be adjusted, and screw the rest to the base. Raise or lower it with wedges between slide and base, and clamp it to the bed like the tailstock.

Material untuk langkah ini:

Papan Kayu KerasPapan Kayu Keras1 buah
Baut kepala bulat leher persegiBaut kepala bulat leher persegi1 buah
Mur Segi EnamMur Segi Enam1 buah
Sekrup kayuSekrup kayu1 buah

Alat yang dibutuhkan:

Gergaji TanganGergaji Tangan
Pahat kayuPahat kayu
Bor engkol dan mata borBor engkol dan mata bor
10

Troubleshooting

Wood lathe troubleshooting.

Flow

Loading...
11

History and honest limits

From "How to Make a Wood Lathe" by E. E. Hulgan, Marion, Ind., in **The Boy Mechanic, Book 2**, Popular Mechanics, 1915 (Project Gutenberg 44585; checked on the archive.org scan boymechanicbook200chic2, pp. 434-436). Part shapes come from his Figs. 1-9; he gives no pulley material and no countershaft or foot-drive details. The pulley material, tools and metric figures are ours.

Bahan

12

Alat yang Diperlukan

15

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...