SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
MASA DEPAN HIJAU
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Building an Infrared Distance Sensor
Ed

Dibuat oleh

Ed

13. Juli 2026FI
0
0
0
0
0

Building an Infrared Distance Sensor

Measure distance with light. A Sharp infrared sensor bounces a beam off an object and reports, as a voltage, the angle it returns at — closer objects give a higher reading. The Arduino turns that into an approximate distance and lights an LED when something comes near: a touchless switch, a hand-wave trigger, or a robot's eyes. Unlike the ultrasonic sensor, this uses infrared light, works at short range, and makes no sound.

Menengah
1 hour

Instruksi

1

Wire the sensor and LED

The Sharp sensor has a 3-wire cable: VCC (red) to Arduino 5V, GND (black) to GND, and signal (white or yellow) to A0. On the breadboard, wire an LED from pin 7 through a 330 Ω resistor to GND (long leg to the pin).

Material untuk langkah ini:

Arduino Uno R3Arduino Uno R31 buah
Infrared Proximity Sensor - Sharp GP2Y0A21YKInfrared Proximity Sensor - Sharp GP2Y0A21YK1 buah
LED - Basic 5mmLED - Basic 5mm1 buah
Resistor 330 Ohm 1/6 Watt PTH - 20 packResistor 330 Ohm 1/6 Watt PTH - 20 pack1 bungkus
BreadboardBreadboard1 buah
Jumper Wires (Male-to-Male)Jumper Wires (Male-to-Male)1 bungkus
2

Connect and open the IDE

Plug the Arduino into your computer with the USB cable, open the Arduino IDE, and select Arduino Uno and its serial port.

Material untuk langkah ini:

USB-B CableUSB-B Cable1 buah

Tools needed:

Computer with Arduino IDEComputer with Arduino IDE
3

Upload the distance sketch

Paste this sketch and upload, then open the Serial Monitor. It reads the sensor, estimates the distance, and lights the LED when something is within 20 cm.

ir_distance_sensor.inoarduino
// Sharp GP2Y0A21YK infrared distance sensor (valid ~10-80 cm).
// The output is NON-LINEAR (roughly 1/distance); the formula below is a common
// approximation - calibrate against known distances if you need accuracy.
// Sensor signal on A0; indicator LED on pin 7.

const int IR_PIN = A0;
const int LED_PIN = 7;
const int NEAR_CM = 20;   // light the LED when something is closer than this

void setup() {
  pinMode(LED_PIN, OUTPUT);
  Serial.begin(9600);
}

void loop() {
  int raw = analogRead(IR_PIN);
  float volts = raw * (5.0 / 1023.0);

  // approximate distance in cm for the GP2Y0A21 curve
  float distance = 27.86 * pow(volts, -1.15);

  Serial.print(distance);
  Serial.println(" cm");

  if (distance < NEAR_CM) {
    digitalWrite(LED_PIN, HIGH);   // object nearby
  } else {
    digitalWrite(LED_PIN, LOW);
  }
  delay(200);
}
4

Test and understand the curve

Open the Serial Monitor and move your hand between about 10 and 80 cm — the printed distance should track it, and the LED lights inside 20 cm. Two things to know: below ~10 cm the reading becomes ambiguous (the sensor's curve folds back), and the output is non-linear, so for real accuracy note the raw value at a few known distances and fit your own curve.

5

Put it to work

Use it as a touchless switch (wave to trigger), a shelf or drawer 'is-it-open' sensor, or an obstacle detector for a small robot. Change NEAR_CM to set the trigger distance, or swap in the short-range (4–30 cm) or long-range (20–150 cm) Sharp sensor for a different span.

Bahan

7

Alat yang Diperlukan

1
Estimasi total
$64.00

Blueprint terkait

Blueprint ini berbagi pengetahuan — teknik, bahan, atau prinsip

Building an Ultrasonic Parking Sensoroleh Ed
Blinking LED — Your First Arduino Projectoleh Admiral OOM

Related blueprints

Other builds that share materials, tools, or techniques with this one.

Building an Ultrasonic Parking Sensorelectronics
Building an Air-Quality Monitorelectronics
Building a Carbon Monoxide Detectorelectronics
Building a Methane Gas Leak Detectorelectronics
Controlling a Stepper Motor with an EasyDriverelectronics
Using an LCD — SIK Circuit 15electronics

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Loading comments...