Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Camera Tripod: a Four-Fold Ash Tripod Stand (Hasluck, 1902)
Woody

Dibuat oleh

Woody

4. November 2026NO
9
0
0
0
0

Camera Tripod: a Four-Fold Ash Tripod Stand (Hasluck, 1902)

A light, compact folding camera stand: three legs, each of seven ash laths riveted so it folds in four, locked open by brass buttons, on a triangular ash top with brass pins and a hole for the camera screw. Hasluck says the same method makes stands that fold in three or two. Source: Paul N. Hasluck, Photographic Cameras and Accessories (1902), pp. 153-157. Picture: Figs. 226-230 of the book.
Menengah
Unknown

Instruksi

1

Cut the ash laths

Cut laths of good ash, true and square or the stand won't be rigid, and round the edges slightly: six 17 1/4 x 5/8 x 3/8 in, six 16 x 5/8 x 3/8 in, six 15 1/2 x 5/8 x 3/8 in, and three 14 x 5/8 x 5/8 in.

Material untuk langkah ini:

Papan kayu ashPapan kayu ash1 21 laths

Alat yang dibutuhkan:

Gergaji punggungGergaji punggung
Ketam blokKetam blok
2

Fit the top ends and stretcher

On each 17 1/4 in lath let in flush a 1/16 in brass plate, 1 1/4 in long, with a 3/16 in hole 1/4 in from the top, held by two countersunk brass screws; bore the wood to match and take off the top corners. On one lath of each pair cut a groove inside, about 3/16 in deep and 3 1/2 in long, starting 2 in from the top, and hinge a 1/8 in brass rod stretcher in it on a pin. On the other lath cut a curved groove 1 1/2 in long, 3/16 in wide, with a small hole at the bottom where the rod catches.

Material untuk langkah ini:

Lembaran KuninganLembaran Kuningan1 1/16 in plates
Sekrup kayuSekrup kayu1 small brass screws
Batang KuninganBatang Kuningan1 1/8 in stretcher

Alat yang dibutuhkan:

Rangka Gergaji Besi dengan BilahRangka Gergaji Besi dengan Bilah
Kikir LogamKikir Logam
Bor tanganBor tangan
Pahat kayuPahat kayu
Obeng pipihObeng pipih
3

Bore and rivet the legs

Bore the rivet holes: in the long laths 1 3/4 in from the lower end, counterbored so the copper rivet head sits flush, then 1/8 in through; in the 16 in and 15 1/2 in laths 1/2 in and 1 3/4 in from the ends; in each 14 in piece 1/2 in from one end, and taper its other end for a pointed iron shoe or a steel point and ferrule. Rivet the 21 laths into three legs with 1/8 in copper rivets and washers: a 16 in lath inside each 17 1/4 in one, a 15 1/2 in lath inside that, the 14 in foot between the last pair. Rivets flush, just tight enough to fold but not loose.

Material untuk langkah ini:

Paku keling tembagaPaku keling tembaga1 1/8 in, with washers
Logam tidak diketahuiLogam tidak diketahui3 iron shoes or steel points

Alat yang dibutuhkan:

Bor engkol dan mata borBor engkol dan mata bor
Bor tanganBor tangan
Palu kelingPalu keling
4

Add cross strips and lock buttons

Screw 1/16 in brass strips across the bottom ends of each pair of laths (Fig. 229). Under them screw strips carrying a small brass button riveted at the centre; turned, the button hooks over the strip above and locks the joint open (Fig. 230).

Material untuk langkah ini:

Lembaran KuninganLembaran Kuningan1 cross strips, buttons
Sekrup kayuSekrup kayu1 buah

Alat yang dibutuhkan:

Rangka Gergaji Besi dengan BilahRangka Gergaji Besi dengan Bilah
Kikir LogamKikir Logam
Obeng pipihObeng pipih
Palu kelingPalu keling
5

Make the top

Plane ash to 1/2 in and draw an equilateral triangle with 8 1/2 in sides. Bisect the angles; 2 in from each corner draw a line at right angles, go 1/2 in in along the sides, and mark three rectangles 2 7/8 x 3/4 in; cut the outline (Fig. 231). Fix a 3/16 in brass rod, one end tapered, across each rectangle, bored 3/8 in from the outer edge and projecting about 1/2 in, for the legs to hang on. Bore a 1/4 in hole in the centre for the camera screw and glue felt on top.

Material untuk langkah ini:

Papan kayu ashPapan kayu ash1 top
Batang KuninganBatang Kuningan3 3/16 in pins
Kain kempa wolKain kempa wol1 buah
Lem hewaniLem hewani1 buah

Alat yang dibutuhkan:

Ketam blokKetam blok
Gergaji punggungGergaji punggung
Bor engkol dan mata borBor engkol dan mata bor
Bor tanganBor tangan
6

Finish

Glasspaper and varnish the wood, and lacquer the brass.

Material untuk langkah ini:

Pernis sirlakPernis sirlak1 varnish
Bahan tidak diketahuiBahan tidak diketahui1 brass lacquer

Alat yang dibutuhkan:

AmplasAmplas

Bahan

10

Alat yang Diperlukan

10

Cetak biru ini membuat

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...