Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Screw-Depth Portable Router: The Motor's Threaded Casing Screws Into a Split Base, One Turn per Sixteenth (Carter, 1924)
Forge

Dibuat oleh

Forge

13. November 2026NO
8
0
0
0
0

Screw-Depth Portable Router: The Motor's Threaded Casing Screws Into a Split Base, One Turn per Sixteenth (Carter, 1924)

Ray L. Carter of Syracuse, New York, received US 1,514,894, dated 11 November 1924, for the portable electric router: a small high-speed motor in an insulated casing light enough to hold in one hand, with a cutter in a chuck on its shaft. The casing is threaded outside and screws into the split, threaded top of a hollow base with a flat bottom. Each turn moves the cutter 1/16 inch, and a clamp screw across the split locks it. The base is cut away so the cutter can be seen and the chips can get out. We print the casing and base in PETG at his pitch, round a small DC motor. The other sizes are ours.
Menengah
About 2 days

Instruksi

1

One turn, one sixteenth

Memuat notebook Jupyter…
2

Read US 1,514,894

"In practice, the threads of the shell 3 and support 9 are preferably about one-sixteenth inch pitch, so that each revolution of the motor or support in either direction moves the tool A correspondingly."
3

Print the motor casing

The casing 3: a tube for a 42 mm motor with a 60 mm thread at 1/16 inch pitch, an 18 mm hole and air slots in its bottom, and two holes 29 mm apart for the motor's face screws. Print it bottom down. PETG, 0.2 mm layers, 40 % infill, 5 walls; no supports.
Berkas desainSTLCC0 - Free
4

Print the base

The support 9: a hollow base with a flat plate 140 mm across and an opening 50 mm wide, its sides cut away, two wings, and the split, threaded top with clamp lugs. Print it plate down. PETG, 0.2 mm layers, 40 % infill, 5 walls; no supports.
Berkas desainSTLCC0 - Free
5

Print and fit the parts

Print the casing and the base in PETG. Clean the threads and screw the casing into the base by hand; it should turn smoothly all the way. If it is tight, run it in and out a few times. Check the base's bottom is flat by rubbing it on abrasive paper on a flat board.

Material untuk langkah ini:

Filamen PETGFilamen PETG1 buah

Alat yang dibutuhkan:

Pencetak 3D filamen (FDM)Pencetak 3D filamen (FDM)
Alat penghilang duri sisaAlat penghilang duri sisa
Jangka Sorong Digital 6 InciJangka Sorong Digital 6 Inci
6

Motor, collet and wiring

Fit the collet adapter on the motor's shaft and tighten its set screws. Push the motor down into the casing so its face sits on the casing's bottom with the collet through the hole, and screw it in with its two M4 face screws. Solder the supply leads through a toggle switch, sleeve the joints, and lead the cable out through the casing's open top. Set the DC supply to the motor's rated voltage.

Material untuk langkah ini:

Motor listrikMotor listrik1 buah
Adaptor kolet poros motorAdaptor kolet poros motor1 buah
Sekrup Kepala SoketSekrup Kepala Soket2 buah
Sakelar tuasSakelar tuas1 buah
Kawat hubungKawat hubung1 buah
Selongsong bakarSelongsong bakar1 buah

Alat yang dibutuhkan:

Sumber daya arus searahSumber daya arus searah
Solder ListrikSolder Listrik
Set kunci LSet kunci L
Kunci InggrisKunci Inggris
7

Set the depth and lock it

Fit a straight bit in the collet. Screw the casing into the base until the bit's end is level with the base's bottom on a flat board, then screw it in four more turns for a 1/4 inch (6.35 mm) deep cut. Put an M5 screw through the lugs with a wing nut and tighten it, closing the split on the thread.

Material untuk langkah ini:

Sekrup Kepala SoketSekrup Kepala Soket1 buah
Mur sayapMur sayap1 buah

Alat yang dibutuhkan:

Set mata mesin profilSet mata mesin profil
Set kunci LSet kunci L
Jangka Sorong Digital 6 InciJangka Sorong Digital 6 Inci
8

Rout a groove

Clamp a board down. Hold the router by its casing and wings, base flat on the board, switch on, and move it along a clamped straightedge so the bit cuts a groove. Take deep grooves in two or three passes, a few turns deeper each time.

Alat yang dibutuhkan:

Papan Kayu KerasPapan Kayu Keras
Klem batangKlem batang
Kacamata pengamanKacamata pengaman
9

Troubleshooting

Router troubleshooting.

Flow

Loading...
10

History and honest limits

**Ray L. Carter** of Syracuse, New York, US 1,514,894, dated 11 November 1924, filed 29 September 1923. He claimed a motor with a threaded casing, "a hollow cylinder having a split threaded portion adapted to engage the threaded portion of said casing whereby said tool may be moved relatively to the work", a plane bottom to move over the work, and means for locking. His motor ran on mains through a lamp socket at over 7,000 r.p.m.; ours is a small DC motor on a bench supply, a light-duty router. His casing was insulating material; ours is printed PETG. His fan and baffle disk are left out. The pitch is his; the other sizes are ours.

Bahan

8
  • Placeholder
  • Placeholder
  • Placeholder
  • Placeholder
  • 1 buah
    1 vendor sell this, none ship to you yet
    Placeholder
  • 1 buah
    2 vendors sell this, none ship to you yet
    Placeholder
  • Placeholder
  • 1 buah
    Placeholder

Alat yang Diperlukan

11

Berkas desain

2

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...