SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Claw Hammer: Drop-Forged Head, Turned Wooden Handle
A claw hammer's head is high-carbon steel, hot forged between dies and then hardened only where it takes the blows: the face, the poll and the claws. The handle is straight-grained ash or hickory, woods with good strength, durability and enough give to absorb the shock of repeated blows. It is turned on a lathe that copies a cam, pushed up through the head's eye and wedged: one thin wooden wedge driven diagonally into a slot, then two steel wedges driven through it crossways.
Lanjutan
Factory process
Instruksi
1
1
Heat the bar
Heat the bar
Heat a length of steel bar to about 1,200–1,300 °C (2,200–2,350 °F) with open flame torches or by passing it through an induction coil.
Material untuk langkah ini:
Batang baja perkakas persegi1 as requiredAlat yang dibutuhkan:
Pemanas induksi2
2
Forge the head
Forge the head
Put the hot bar or a cut blank between the dies. The ram forces them together and squeezes the steel into the die cavities; repeat in several dies to form the head step by step.
Alat yang dibutuhkan:
Palu jatuh dengan cetakan tempa3
3
Trim the flash
Trim the flash
Cut off the flash, the steel squeezed out between the dies, with trimming dies. Cool the head and grind off rough spots.
Alat yang dibutuhkan:
Die pemangkas sirip
Gerinda duduk4
4
Harden the face, poll and claws
Harden the face, poll and claws
Heat those areas with a flame or an induction coil and cool them quickly, so the steel near the surface becomes much harder than the rest of the head.
Alat yang dibutuhkan:
Pemanas induksi5
5
Clean and polish
Clean and polish
Shot blast the head (a stream of air carrying small steel particles), paint it if wanted, then polish the face, poll, claws and cheeks. Smooth the V-slot of the claws with an abrasive disc.
Alat yang dibutuhkan:
Kabin shot blasting
Roda poles6
6
Turn the handle
Turn the handle
Cut ash or hickory to length and hold it at both ends in the lathe. As it spins, the cutting tool follows a cam with the handle's shape. Cut a slot diagonally across the top and sand the handle smooth.
Material untuk langkah ini:
Kayu Keras Bahan Gagang1 buahAlat yang dibutuhkan:
Mesin bubut gagang berpemandu cam
Amplas7
7
Hang the head
Hang the head
Push the handle up through the eye of the head. Tap the wooden wedge into the diagonal slot to spread the handle against the head, then drive two small steel wedges through it crossways.
Material untuk langkah ini:
Pasak kayu keras1 buah
Baji silang baja2 buahBahan
4- 1 as requiredPlaceholder
- 1 buahPlaceholder
- 1 buahPlaceholder
- 2 buahPlaceholder
Alat yang Diperlukan
8- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
Cetak biru ini membuat
Blueprint terkait
Blueprint ini berbagi pengetahuan — teknik, bahan, atau prinsip
CC0 Domain Publik
Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.
Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.