Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Hat Pin With a Hat-Coil and a Hair-Coil, Screwed In and Out (Condra, 1906)
Forge

Dibuat oleh

Forge

13. November 2026NO
10
0
0
0
0

Hat Pin With a Hat-Coil and a Hair-Coil, Screwed In and Out (Condra, 1906)

Elizabeth S. Condra of Corona, California, received US 814,833, dated 13 March 1906, for a hat pin that will not work itself out of the hat. Two small coils are bent into the pin: a short one at the point that screws through the hat, and a longer one in the middle that screws into the hair. Turned in, it holds; turned the other way, it comes out. We bend it from steel wire with a glass bead for the head. All sizes are ours.
Pemula
About 1 hour

Instruksi

1

How much wire

Memuat notebook Jupyter…
2

Read US 814,833

"The insertion of the pin is accomplished with the least possible manipulation, as the hat-coil 4 is first passed through one side of the hat, then through the hair, and then through the other side of the hat."
3

Cut and straighten the wire

Cut 1.6 mm steel wire to the length from the notebook. Draw it through a fold of cloth between your fingers, or roll it under a flat board, until it is straight.

Material untuk langkah ini:

Kawat bajaKawat baja1 buah

Alat yang dibutuhkan:

Tang potongTang potong
Meteran GulungMeteran Gulung
4

Sharpen the point

Hold the wire in the vice and file one end to a long, even point, turning it as you go. Finish on a sharpening stone so it slips through felt and straw without tearing them.

Alat yang dibutuhkan:

Set Kikir JarumSet Kikir Jarum
Ragum MejaRagum Meja
Batu AsahBatu Asah
5

Bend the hat-coil

About 6 mm from the point, wind the wire two turns round a 3 mm rod, spacing them about 3 mm apart, like a small corkscrew. Bend the wire on each side back so the point and the rest of the pin run straight along the coil's middle: her "axis in line with the rod".

Alat yang dibutuhkan:

Batang Baja LunakBatang Baja Lunak
Tang berujung bulatTang berujung bulat
Tang Berujung RataTang Berujung Rata
6

Bend the hair-coil

At the place the notebook gives, wind five turns the same way round the same rod, in the same direction as the hat-coil, so one turn of the pin drives both. Bend the ends back in line again. Sight along the pin: the straight parts should all lie on one line.

Alat yang dibutuhkan:

Batang Baja LunakBatang Baja Lunak
Tang berujung bulatTang berujung bulat
Tang Berujung RataTang Berujung Rata
7

Fit the head

Cut the end square at the finished length and roughen it with sandpaper. Fill the hole of a glass bead with epoxy and push it on, her head or knob 3. It turns the pin and stops it going too far. Leave it to set as the epoxy's label says.

Material untuk langkah ini:

Manik kacaManik kaca1 buah
Epoksi dua komponenEpoksi dua komponen1 buah

Alat yang dibutuhkan:

Tang potongTang potong
AmplasAmplas
8

Put it in

Turn the hat-coil through one side of the hat. Push the pin straight across, without turning, until the hat-coil reaches the far side. Then turn it again: one coil goes through the hat and the other into the hair, and the head comes against the hat. To take it out, turn it back the other way and draw it out.
9

Troubleshooting

Coiled hat pin troubleshooting.

Flow

Loading...
10

History and honest limits

**Elizabeth S. Condra** of Corona, California, US 814,833, dated 13 March 1906, filed 22 August 1904. She claimed "a hat-pin comprising a metal rod having one end sharpened to form a tip or point, a head at the other end, the rod being provided with a hat-coil and a hair-coil". She wrote that it will be impossible for it to work itself out of the hat "as so frequently happens with a straight pin". She gives no sizes: the steel wire, the 230 mm length, the coil size and number of turns, the glass bead and the epoxy are ours.

Bahan

3

Alat yang Diperlukan

9

Cetak biru ini membuat

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...