Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI

Christmas Tree Stand: Three Legs Tied by Wire Links to a Nail in the Butt (Cook, 1902)
William Cook of New York received US 710,762, dated 7 October 1902, for a Christmas tree stand of three leaning legs and three wire links. The links meet under the tree on a nail driven up into the butt, and their other ends are fixed part way up the legs. The tops of the legs are screwed to the trunk. The tree's weight pushes the feet out, the links pull back, and the tops of the legs squeeze the trunk.
We make it from pine and steel wire. All sizes are ours.
Pemula
About 3 hours
Instruksi
1
1
Where the links go
Where the links go
Memuat notebook Jupyter…
2
2
Read US 710,762
Read US 710,762
"The tendency of legs A to spread by weight of tree causes an outward tension at wire nail F through the several links C and inward pressure on stem of tree by upper part of legs A. Thus the tree is held very secure and perfectly upright by two opposite forces acting a short space apart and derived from weight of tree."
3
3
Cut the legs
Cut the legs
Saw three legs 700 mm long from 70 x 22 mm pine (ours). Set a bevel gauge to 30 degrees and cut both ends of each leg at that angle, parallel to each other, so the foot sits flat on the floor and the top lies along the trunk, as in his Fig. 2. Sand off the splinters.
Material untuk langkah ini:
Papan pinus1 buahAlat yang dibutuhkan:
Gergaji Tangan
Perusut sudut
Meteran Gulung
Pensil
Amplas4
4
Bend the links
Bend the links
Cut three pieces of 2.5 mm steel wire, each the link length from the notebook plus about 60 mm for the eyes. Bend a round eye at each end with round-nose pliers, as his Fig. 3, so the eyes' centres are the link length apart. Make all three the same.
Material untuk langkah ini:
Kawat baja3 buahAlat yang dibutuhkan:
Tang potong
Tang berujung bulat
Meteran Gulung5
5
Staple the links to the legs
Staple the links to the legs
Mark each leg where the notebook says, on its inner face. Bend three U staples from the same wire (ours). Lay a link's outer eye on the mark and drive a staple over it into the leg, his staple H, leaving the eye free to turn.
Material untuk langkah ini:
Kawat baja1 buahAlat yang dibutuhkan:
Tang potong
Tang berujung bulat
Palu cakar6
6
Drill the tops of the legs
Drill the tops of the legs
Drill a hole through the top of each leg, about 40 mm from its end, just big enough for the screw eye's shank to pass.
Alat yang dibutuhkan:
Bor tangan7
7
Nail the links to the butt
Nail the links to the butt
Saw the butt of the tree off square. Lay the tree on its side. Thread a long wire nail through the three free eyes of the links, his nail F, and drive it up into the middle of the bottom end of the tree.
Material untuk langkah ini:
Paku1 buahAlat yang dibutuhkan:
Gergaji Tangan
Palu cakar8
8
Fix the tops of the legs
Fix the tops of the legs
Bring the top of each leg in against the trunk. Make a start hole in the trunk with an awl through the leg's hole, and turn a screw eye through the leg into the trunk until the leg is held tight, his screw-eye D. Do all three, then stand the tree up.
Material untuk langkah ini:
Sekrup mata3 buahAlat yang dibutuhkan:
Penusuk (Uncek)9
9
Check it stands upright
Check it stands upright
All three feet should touch the floor and the links should be straight and tight. Look at the tree from two sides. To take it down, turn out the screw eyes and pull the nail; the links fold about the nail for storing.
10
10
Troubleshooting
Troubleshooting
Christmas tree stand troubleshooting.
Flow
Loading...
11
11
History and honest limits
History and honest limits
**William Cook** of New York, US 710,762, dated 7 October 1902, filed 29 July 1901. He claimed "a Christmas-tree stand composed of legs, and links, one end of each link being connected with one leg at a point intermediate between the ends of the leg, and the opposite ends of the links being connected with each other to form a seat". He says the stand is "more economical of construction and more easily applied" and that "size of tree offers no obstacle". He names no materials and gives no sizes: the pine, the wire, the 700 mm legs, the 30 degree angle, the butt height and how the screw eyes pass through the legs are ours. His drawing also marks parts E and G, which his text does not describe.
Bahan
4- 1 buahPlaceholder
- 4 buahPlaceholder
- 1 buahPlaceholder
- 3 buahPlaceholder
Alat yang Diperlukan
10- Placeholder
- Placeholder
- 1 vendor sell this, none ship to you yetPlaceholder
- 1 vendor sell this, none ship to you yetPlaceholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
Cetak biru ini membuat
Blueprint terkait
Blueprint ini berbagi pengetahuan — teknik, bahan, atau prinsip
CC0 Domain Publik
Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.
Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.


