Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI

Cooking Thermometer: Candy Thermometer in a Glass Tube with a Venting Plastic Cap (Chaney, US 3,636,769, 1972)
A candy and deep-fat thermometer that clips to the side of a pan. A glass thermometer on a printed scale card sits inside a protective glass tube, so it never touches the candy. The top of the tube is closed by a polyethylene cap that seals in normal use but softens when the whole thermometer is heated far too hot, as in an oven, so the air inside escapes instead of bursting the tube.
Result: a pan-side cooking thermometer that cannot explode if overheated.
Source: J. L. Chaney, US 3,636,769 (1972). Unknown: the scale range, sizes and several materials. Picture: the patent drawing.
Menengah
Unknown
Instruksi
1
1
Mount the thermometer on its scale
Mount the thermometer on its scale
Fasten a glass thermometer tube to a graduated scale card with small fasteners, the bulb at the bottom. The patent's card is marked with cooking points such as soft ball, hard ball, soft crack, hard crack, fish, fowl, potatoes and doughnuts. Fix a disk on top of the card to keep it centred in the outer tube. Not given: the range, the card and fastener materials.
Material untuk langkah ini:
Termometer Laboratorium1 thermometer tube
Bahan tidak diketahui1 scale card, disk
Logam tidak diketahui1 fastenersAlat yang dibutuhkan:
Dimensi tidak diketahui2
2
Enclose it in the protective tube
Enclose it in the protective tube
Slide the card and thermometer into a glass protective tube, open at the top, so the bulb reaches the lower end and touches a metal cap there to pass on the heat. Not given: the tube size, the metal of the end cap, how the cap is joined to the tube.
Material untuk langkah ini:
Tabung kaca1 protective tube
Logam tidak diketahui1 end capAlat yang dibutuhkan:
Dimensi tidak diketahui3
3
Fit the venting cap
Fit the venting cap
Close the open top with a cup-shaped cap of a thermoplastic such as polyethylene, a friction fit that seals out dirt. Polyethylene softens at about 180 °F and melts near 250 °F: if the thermometer is heated in an oven to 400-550 °F, the air inside would reach 12-14 psi, but the cap distorts first and lets it out. Do not use rubber or a thermosetting plastic, which does not vent. Ours: LDPE.
Material untuk langkah ini:
Pelet LDPE1 capAlat yang dibutuhkan:
Dimensi tidak diketahui4
4
Fit the pan clip and use it
Fit the pan clip and use it
Slide a spring clip onto the outside of the tube; its spring arm holds the thermometer upright over the edge of the pan. Clip it on with the bulb end in the candy or fat and read the scale; it also serves for deep frying. Ours: spring steel wire.
Material untuk langkah ini:
Kawat baja pegas1 clipAlat yang dibutuhkan:
Tang berujung bulatBahan
6- 1 thermometer tubePlaceholder
- 1 scale card, diskPlaceholder
- 1 end capPlaceholder
- 1 protective tubePlaceholder
- 1 capPlaceholder
- 1 clipPlaceholder
Alat yang Diperlukan
2- Placeholder
- Placeholder
Bahan cetak biru terhubung

Berbahaya
10% Atribusi
Liquid-in-Glass Thermometer: Bulb, Fill, Seal and Scale
oleh Penny
Pengerjaan Kaca
42
0
0
0
1
0

Berbahaya
10% Atribusi
LDPE Pellets: Ethylene Polymerised at 1500 Atmospheres with a Trace of Oxygen
oleh Charlie
Industri
14
0
0
0
2
0

10% Atribusi
Spring Steel Strip and Wire, Hardened and Tempered
oleh Forge
Pengerjaan Logam
48
0
0
0
5
0
Cetak biru ini membuat
CC0 Domain Publik
Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.
Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.
