SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI

Counter-Rotating Egg Beater: One Wheel, Two Beaters Turning Opposite Ways
A single whisk carries the egg round with it rather than cutting through it.
James F. Monroe of Fitchburg, Massachusetts, and E. P. Monroe of New York received US 23,694, dated 19 April 1859, for an egg beater: a frame clamped to a table carries a bevel wheel turned by a handle, gearing into two pinions on opposite sides of it; one turns an inner beater of bent wires, the other an outer beater round it, "in opposite directions."
This rung works out the beater speeds, then prints the crown wheel and pinions, bends the beaters, and times a beating.
Menengah
About 5 hours, plus printing
Instruksi
1
1
Beater speeds
Beater speeds
Memuat notebook Jupyter…
2
2
The gear train it uses
The gear train it uses
The embedded blueprint works gear ratios and direction. Monroe takes two pinions off opposite sides of one wheel so they turn opposite ways.
3
3
Read US 23,694
Read US 23,694
"This invention consists in arranging in an adjustable frame two beaters, one inside the other, which receive motion in opposite directions by means of two pinions which gear into a large bevel wheel and on opposite sides of the same, so that by rotating the bevel wheel by means of a handle the beaters receive the required motion."
4
4
Print the gears
Print the gears
Print the 48-tooth crown wheel (/uploads/blueprints/counter-rotating-egg-beater-crown-wheel.stl) and two 12-tooth pinions (/uploads/blueprints/counter-rotating-egg-beater-pinion.stl). Print in PETG at 0.2 mm layers, 30 % infill, 4 walls.
Material untuk langkah ini:
Filamen PETG1 buahAlat yang dibutuhkan:
Pencetak 3D filamen (FDM)5
5
Build the frame
Build the frame
Cut a plywood upright and two arms. Bolt the crown wheel to the upright on an M5 screw with washers so it turns freely, and fix a handle screw near its rim. Drill the arms 5 mm on the line through both pinions' centres.
Material untuk langkah ini:
Lembaran kayu lapis1 buah
Sekrup mesin1 buah
Ring Rata1 buah
Mur Segi Enam1 buah
Sekrup kayu #8 x 1"1 buahAlat yang dibutuhkan:
Gergaji Coping
Bor Tanpa Kabel
Set Mata Bor
Kunci Inggris
Set obeng6
6
Arbor and inner beater
Arbor and inner beater
Cut 200 mm of 5 mm rod. Epoxy one pinion on it to mesh at the wheel's top, and bend two wire loops 28 mm across at its lower end.
Material untuk langkah ini:
Batang Baja Lunak1 buah
Kawat baja nirkarat1 buah
Epoksi dua komponen1 buahAlat yang dibutuhkan:
Gergaji Besi
Tang berujung bulat
Tang Berujung Rata7
7
Sleeve and outer beater
Sleeve and outer beater
Glue the second pinion to a length of silicone tube sleeved loosely over the rod, meshing at the wheel's bottom. Bend two wire loops 48 mm across and fix them to the sleeve's lower end, round the inner beater.
Material untuk langkah ini:
Kawat baja nirkarat1 buah
Epoksi dua komponen1 buahAlat yang dibutuhkan:
Tang berujung bulat
Tang Berujung Rata
Jangka Sorong Digital 6 Inci8
8
The patent drawing
The patent drawing
US 23,694 drawing sheet, public domain (expired patent).

9
9
Beat egg whites
Beat egg whites
Clamp the frame to the table over the bowl with two egg whites. Turn the handle about once a second and time how long until they hold stiff peaks.

Material untuk langkah ini:
Telur2 buahAlat yang dibutuhkan:
Mangkuk aduk baja nirkarat (besar)
Stopwatch10
10
Beaters that turn together, jam or clash
Beaters that turn together, jam or clash
Counter-rotating egg beater troubleshooting.
Flow
Loading...
11
11
History and honest limits
History and honest limits
**James F. Monroe** of Fitchburg, Massachusetts, and **E. P. Monroe** of New York, assignors to E. P. Monroe, received US 23,694, dated 19 April 1859, reissued 16 October 1860 (No. 1,062). The frame's fork clamps to a table with a set screw and washer. The second pinion lies loose on the arbor, driving the outer beater whose lower collar turns loosely round the arbor's end. They noted it also mixes paint.
**Honest limits.** FDM prints hold food in their layer lines, so wash well and replace when worn. A crown wheel and spur pinions stand in for his bevel gears, and a silicone sleeve for his loose pinion. Your times are the result.
Bahan
11- 1 buahPlaceholder
- 1 buahPlaceholder
- 1 buahPlaceholder
- 1 buahPlaceholder
- 1 buahPlaceholder
- 1 buahPlaceholder
- 1 buahPlaceholder
- 2 buahPlaceholder
- 2 buahPlaceholder
- 1 buahPlaceholder
- 2 buahPlaceholder
Alat yang Diperlukan
12- Placeholder
- Placeholder
- 1 vendor sell this, none ship to you yetPlaceholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
Blueprint terkait
Blueprint ini berbagi pengetahuan — teknik, bahan, atau prinsip
CC0 Domain Publik
Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.
Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.


