Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Digital Tachometer: Hand-Held Contact Type That Holds Its Reading (Sugiyama, Shimpo, US 4,000,465, 1976)
Ed

Dibuat oleh

Ed

3. November 2026FI
13
0
0
0
0

Digital Tachometer: Hand-Held Contact Type That Holds Its Reading (Sugiyama, Shimpo, US 4,000,465, 1976)

A hand-held digital tachometer. You press the contact head on its shaft against the end of a turning shaft and push the thumb button; a slotted disk inside chops a light beam into pulses, and the pulses counted in a fixed time, set by a quartz clock, appear in the window as the speed. A latch holds the reading after you take the tachometer away, so you can read it even where you could not see the window while measuring. Result: a contact tachometer that shows revolutions per unit time and keeps the last reading. Source: Y. Sugiyama (Shimpo Kogyo), US 4,000,465 (1976). Unknown: the number of holes, the clock, the gate time and the circuit details. Picture: the patent drawing.
Lanjutan
Unknown

Instruksi

1

Make the housing and measuring shaft

Make a cylindrical housing to hold in one hand, with a window in its side for the reading and a push button for the power switch where the thumb falls. Run a measuring shaft out of the front end in bearings and fit a contact head on its tip to press against the shaft being measured. Not given: materials, sizes. Ours: aluminium tube, a ball bearing.

Material untuk langkah ini:

Pipa aluminiumPipa aluminium1 housing
Logam tidak diketahuiLogam tidak diketahui1 measuring shaft
Bantalan PeluruBantalan Peluru1 buah
Bahan tidak diketahuiBahan tidak diketahui1 contact head

Alat yang dibutuhkan:

Mesin Bubut LogamMesin Bubut Logam
Bor tanganBor tangan
Dimensi tidak diketahuiDimensi tidak diketahui
2

Make the pulse generator

Fix a disk on the measuring shaft with a ring of small holes evenly spaced near its edge. Put a light source on one side of the disk and a photodetector on the other: each hole passing makes one pulse. Shape and amplify the pulses. Not given: the number of holes. Ours: an LED and a photodiode.

Material untuk langkah ini:

Bahan tidak diketahuiBahan tidak diketahui1 slotted disk
Aneka LEDAneka LED1 light source
Fotodioda (BPW34)Fotodioda (BPW34)1 photodetector
HambatanHambatan1 set

Alat yang dibutuhkan:

Bor tanganBor tangan
3

Build the counting circuit

Divide a quartz oscillator's clock down to gate pulses one unit of time long. Pass the measurement pulses through an AND gate during each gate pulse into a counter. At the start of each gate pulse a reset pulse clears the counter. After the gate pulse ends, the first measurement pulse that arrives triggers a latch pulse that loads the new count into the display. If the head has been taken off the shaft, no pulse arrives, no latch pulse is made, and the display keeps the last reading until the next measurement or until the power is switched off. Not given: the clock frequency and gate time. Ours: logic ICs and a seven-segment display.

Material untuk langkah ini:

Papan sirkuit cetakPapan sirkuit cetak1 buah
Kristal kuarsaKristal kuarsa1 buah
Aneka IC logikaAneka IC logika1 divider, AND gate, counter, latch, reset
Penggerak Tampilan Tujuh SegmenPenggerak Tampilan Tujuh Segmen1 buah
Tampilan Tujuh Segmen Empat DigitTampilan Tujuh Segmen Empat Digit1 buah
Kawat Timah SolderKawat Timah Solder1 as needed

Alat yang dibutuhkan:

SolderSolder
4

Power it and measure

Fit the battery and the thumb button as the power switch. Press the contact head against the end of the turning shaft so it turns with it, push the button, and read the revolutions in the window, now or after you take the tachometer away.

Material untuk langkah ini:

BateraiBaterai1 buah
Tombol tekanTombol tekan1 buah

Alat yang dibutuhkan:

SolderSolder

Bahan

15

Alat yang Diperlukan

4

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...