Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Steel-Faced Hand Hammers and Sledges: Ball, Fuller, Wedge and Claw Panes, Eye on Two Oval Drifts (Edwinson, 1886)
Forge

Dibuat oleh

Forge

14. November 2026NO
10
0
0
0
0

Steel-Faced Hand Hammers and Sledges: Ball, Fuller, Wedge and Claw Panes, Eye on Two Oval Drifts (Edwinson, 1886)

How smiths made hand hammers and sledges, from George Edwinson's smithing series (Amateur Work, 1886): solid steel, or an iron head with a steel face welded into a slit fork; the eye punched and shaped on two oval taper drifts so the wedged handle cannot work loose. Panes: ball, fuller, wedge and claw.
Lanjutan
A day at the forge

Instruksi

1

His weights

Memuat notebook Jupyter…
2

Read Edwinson

"To make a steel hammer it is only necessary to get a bar of steel the required size, heat, upset, and forge to the selected size and shape."
3

Solid steel route

Heat a steel bar of the size needed, upset it and forge it to shape. Punch the hole for the handle and work it on a taper drift. Tool the hammer off smoothly at a red heat, then heat it and harden it in water.

Material untuk langkah ini:

Baja krusibelBaja krusibel1 buah

Alat yang dibutuhkan:

Perapian pandai besiPerapian pandai besi
Landasan TempaLandasan Tempa
GodamGodam
Tang pandai besiTang pandai besi
Pelebar lubang tirusPelebar lubang tirus
Ember pendingin tempaEmber pendingin tempa
4

Steel-faced route: weld the face

Upset a stout iron bar if it is too thin. Slit one end hot with a hot chisel (his sett) into a fork. Forge a steel bar to a wedge that fits it. Bring the iron to a welding heat and the steel to its own (a separate fire if needed), roll the steel in calcined borax and weld. Reheat with the steel protected by welding mixture or sand, and finish the weld.

Material untuk langkah ini:

Batang besi tempaBatang besi tempa1 buah
Batang baja gelembungBatang baja gelembung1 buah
Serbuk boraksSerbuk boraks1 buah
PasirPasir1 buah

Alat yang dibutuhkan:

Perapian pandai besiPerapian pandai besi
Pahat panasPahat panas
Landasan TempaLandasan Tempa
GodamGodam
Tang pandai besiTang pandai besi
5

Shape the head

Cut off the steel, forge steel and iron up into the face. Fashion the head and pane, punch the handle hole and form it on a taper drift, cut the hammer off the bar and finish it held in crooked bit tongs. If both ends are to be steel, weld in both before cutting off. Panes: ball for riveting, fuller for spreading iron, wedge, or claw for drawing nails.

Alat yang dibutuhkan:

Perapian pandai besiPerapian pandai besi
Pelebar lubang tirusPelebar lubang tirus
Pahat panasPahat panas
Landasan TempaLandasan Tempa
PaluPalu
Tang pandai besiTang pandai besi
6

Shape the eye on two drifts

Use two oval taper drifts: one tapered all round to form the lower side of the eye, the other tapered only on its long sides for the upper part. The eye tapers from both sides across the head, but only from the lower side lengthwise. Round the edges on the underside.

Alat yang dibutuhkan:

Perapian pandai besiPerapian pandai besi
Pelebar lubang tirusPelebar lubang tirus
Landasan TempaLandasan Tempa
PaluPalu
7

Sizes and sledges

Hand hammers usually weigh 1-2 lb (0.45-0.9 kg). Larger fuller or wedge pane hammers of 3-30 lb are sledges; one-handed sledges weigh 3-5 lb; heavier ones get stout ash handles 3-4 ft (0.9-1.2 m) long for two hands.

Alat yang dibutuhkan:

Landasan TempaLandasan Tempa
8

Hang the head

Drive the handle into the eye from below so its end is compressed and fits tight. Cut off the extra wood, split the end with a chisel and drive in a wedge of well-seasoned wood. If the eye tapers two ways, cross-slit and drive two wedges.

Material untuk langkah ini:

Bilet kayu ashBilet kayu ash1 buah
Baji kayuBaji kayu1 buah

Alat yang dibutuhkan:

Pisau TarikPisau Tarik
Pahat kayuPahat kayu
PaluPalu
9

Troubleshooting

Hammer troubleshooting.

Flow

Loading...
10

History and honest limits

From George Edwinson, "Smithing and Forging" (part X), **Amateur Work, Illustrated**, vol. VI (Ward, Lock & Co., 1886-87), pp. 211-214 (checked on the archive.org scan amateurworkillus06lond), pp. 212-214 and figs. 227-235. He gives no temper for the face; the metric figures and tools are ours.

Bahan

7

Alat yang Diperlukan

10

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...