Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Brass Binding-Screw: Body Turned from 5/8 in. Rod, Thumb Screws from 3/8 in. Rod, and a Bent Brass Clamp (Edwinson, 1881)
Volt

Dibuat oleh

Volt

14. November 2026SE
9
0
0
0
0

Brass Binding-Screw: Body Turned from 5/8 in. Rod, Thumb Screws from 3/8 in. Rod, and a Bent Brass Clamp (Edwinson, 1881)

The Victorian battery terminal, from George Edwinson's Electro-plating at Home (Amateur Work, 1881): a brass body turned from 1 1/2 in. of 5/8 in. rod, slotted for the plate and bored for the wire, with thumb screws turned from 3/8 in. rod; or a clamp bent hot from a brass strip with a soldered-on wire piece.
Menengah
Two hours at the lathe

Instruksi

1

His sizes

Memuat notebook Jupyter…
2

Read Edwinson

"Those who may have lathes ... may easily turn up a binding-screw ... out of a 1 1/2 in. length of 5/8 in. brass rod."
3

Turn the body

Cut 1 1/2 in. (38 mm) of 5/8 in. (16 mm) brass rod and turn the body to shape first (his fig. 3: a round head on a tapering neck over a forked foot).

Material untuk langkah ini:

Batang KuninganBatang Kuningan1 buah

Alat yang dibutuhkan:

Gergaji BesiGergaji Besi
Mesin Bubut LogamMesin Bubut Logam
Pahat potong bubutPahat potong bubut
4

Slot and bore

Cut the slot that grips the plate. Bore a hole for the wire through the head, then bore the holes for the screws.

Alat yang dibutuhkan:

Ragum MejaRagum Meja
Gergaji BesiGergaji Besi
Kikir (Kikir Tangan)Kikir (Kikir Tangan)
Bor tanganBor tangan
5

Turn the thumb screws

Turn the screws from 3/8 in. (9.5 mm) brass rod with plain thumb-screw heads (he says milled heads are a mistake). Cut a fine thread on them and tap the holes to match.

Material untuk langkah ini:

Batang KuninganBatang Kuningan1 buah

Alat yang dibutuhkan:

Mesin Bubut LogamMesin Bubut Logam
Pahat potong bubutPahat potong bubut
Set pembuat ulirSet pembuat ulir
6

Bent clamp (variant)

From good malleable brass take a strip 3 in. long, 1/2 in. wide and 1/4 in. thick (76 x 13 x 6 mm). Heat it to a dull red and bend it over a former of hot iron. Cut the piece for the wire and centre screw separately, hard-solder it on and trim it. Fit thumb screws as above. (A clamp may also be cast from a wooden pattern.)

Material untuk langkah ini:

Pita kuninganPita kuningan1 buah
Patri PerakPatri Perak1 buah

Alat yang dibutuhkan:

Perapian pandai besiPerapian pandai besi
Tang pandai besiTang pandai besi
PaluPalu
Obor patri kerasObor patri keras
Kikir (Kikir Tangan)Kikir (Kikir Tangan)
Bor tanganBor tangan
Set pembuat ulirSet pembuat ulir
7

Clean and keep it working

Clean the slot with folded emery cloth and the wire hole with the tang of a file. Now and then oil the screw, work it in and out, and wipe the oil off. Do not screw up too tight.

Alat yang dibutuhkan:

Kikir (Kikir Tangan)Kikir (Kikir Tangan)
8

Troubleshooting

Binding-screw troubleshooting.

Flow

Loading...
9

History and honest limits

From George Edwinson, "Electro-plating at Home", **Amateur Work, Illustrated**, vol. I (1881), p. 81 figs. 3 and 7 and p. 99 (checked on the archive.org scan amateurworkillus11881lond). He gives no thread size. Modern panel binding posts add an insulating bush and a banana-plug socket; this is the 1881 brass terminal. The metric figures and the tools are ours.

Bahan

3

Alat yang Diperlukan

11

Cetak biru ini membuat

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...