Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Whitworth Taps from Cast Tool Steel: Turned, Chased, Fluted and Hardened in Salt Water, with Their Wrench (Edwinson, 1886)
Forge

Dibuat oleh

Forge

14. November 2026NO
10
0
0
0
0

Whitworth Taps from Cast Tool Steel: Turned, Chased, Fluted and Hardened in Salt Water, with Their Wrench (Edwinson, 1886)

George Edwinson's instructions (Amateur Work, 1886) for a home-made set of Whitworth taps, 3/16 to 1 inch, in entry, half-plug and full-plug form: cast tool steel annealed, turned, roughed with a single-point tool and finished with home-made chasers in a screw-cutting lathe, fluted, hardened in swirled salt water and tempered deep yellow; plus the two-hole tap wrench. The dies and stock are in the companion blueprint.
Lanjutan
Several days for a set of thirty

Instruksi

1

His tables

Memuat notebook Jupyter…
2

Read Edwinson

"There is only one perfect method of making a good tap, and that is by turning the metal ... and cutting the thread in a screw-cutting lathe."
3

Cut and anneal the blanks

Cut the best 1 in. square cast tool steel into 3 1/2 in. lengths for the large taps, and 1/2 in. steel into 3 in. lengths for the small ones (a full set takes 5 ft 6 in. of the first and 3 ft of the second). Anneal: blood red, cooled slowly in hot ashes. File the ends square, centre-punch, and drill the centres 1/16 in. (small) or 1/8 in. (large) deep.

Material untuk langkah ini:

Batang baja perkakasBatang baja perkakas1 buah

Alat yang dibutuhkan:

Pahat panasPahat panas
Perapian pandai besiPerapian pandai besi
Kikir (Kikir Tangan)Kikir (Kikir Tangan)
PenitikPenitik
Mesin Bor DudukMesin Bor Duduk
4

Rough out the taps

Turn the corners off. Mark each tap: entry 1/2 in. head, 3/4 in. shank; half plug 1/2 in. head, 1 in. shank; full plug 1/2 in. head, 1 1/4 in. shank; the rest is thread (for the 1 in. set; 7/8 the same, smaller sets in proportion with shanks turned down for clearance). Below 1/2 in. make the square heads 3/8 or 3/16 in. to fit the wrench. Anneal again, turn true and smooth, and finish with a fine file.

Alat yang dibutuhkan:

Mesin Bubut LogamMesin Bubut Logam
Kikir (Kikir Tangan)Kikir (Kikir Tangan)
Perapian pandai besiPerapian pandai besi
5

Make the chasers

From flat tool steel forge one chaser per size, the largest 1 in. wide, 1/4 in. thick and 5 in. long, the rest a little smaller, with 3 1/2 or 4 1/2 teeth across the width and a tang for a wooden handle (fig. 72). Upset the point, grind, anneal, file the teeth, and finish them by running the chaser against a full plug tap or hub of that pitch in the lathe. Inside chasers: against a left-handed hub, or file off the lower leading edge of each tooth (fig. 74).

Material untuk langkah ini:

Batang baja perkakasBatang baja perkakas1 buah

Alat yang dibutuhkan:

Perapian pandai besiPerapian pandai besi
Landasan TempaLandasan Tempa
PaluPalu
Kikir (Kikir Tangan)Kikir (Kikir Tangan)
Mesin Bubut LogamMesin Bubut Logam
6

Cut the threads

Rough each thread with a single fine-point tool in the slide rest of a screw-cutting lathe, set with the change wheels for its pitch (notebook), then finish with the chaser. Whitworth form: 55 degree angle, one-sixth rounded off top and bottom. Stamp each tap with its size and threads per inch.

Alat yang dibutuhkan:

Mesin Bubut LogamMesin Bubut Logam
PaluPalu
7

Flute and point

Cut three flutes along each tap with a circular cutter in the lathe or a thin emery wheel (before hardening), or grind the sides flat (fig. 75). Grind fully 1/2 in. of each entry tap to a taper and the first few threads of the half plug; leave the full plug entire.

Alat yang dibutuhkan:

Mesin Bubut LogamMesin Bubut Logam
Gerinda dudukGerinda duduk
8

Harden and temper

Heat each tap or chaser to blood red and plunge it straight down into a pail of water with a handful of common salt, swirled with a stick, into the middle of the swirl so it does not warp. Rub part bright, lay it in angle or grooved iron over a clear fire or a Bunsen burner until the bright part is deep yellow, then dip it in cold water. Grind the chaser tops level.

Material untuk langkah ini:

GaramGaram1 buah
AirAir1 buah

Alat yang dibutuhkan:

Perapian pandai besiPerapian pandai besi
EmberEmber
Pembakar BunsenPembakar Bunsen
Gerinda dudukGerinda duduk
9

Make the tap wrench

Take 10 in. of 3/4 in. round steel or iron. Heat the middle, upset it and flatten 2 1/2 in. to 1/2 in. thick. Drill two small holes and open them with a square punch, one to 3/8 in. and one to 1/4 in. Straighten, anneal, centre the ends and turn them in the lathe, then harden and temper. A longer, heavier wrench with one 1/2 in. hole suits the big taps.

Material untuk langkah ini:

Batang baja perkakasBatang baja perkakas1 buah

Alat yang dibutuhkan:

Perapian pandai besiPerapian pandai besi
Landasan TempaLandasan Tempa
GodamGodam
Mesin Bor DudukMesin Bor Duduk
Mesin Bubut LogamMesin Bubut Logam
10

Troubleshooting

Tap troubleshooting.

Flow

Loading...
11

History and honest limits

From George Edwinson, "Smithing and Forging" V, **Amateur Work, Illustrated**, vol. V (1886), pp. 434-438 and figs. 71-77 (checked on the archive.org scan amateurworkillus05lond). He himself advised buying Whitworth gear rather than making it. Metric conversions and the tools listed are ours.

Bahan

3
  • Placeholder
  • 1 buah
    Placeholder
  • 1 buah
    Placeholder

Alat yang Diperlukan

12

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...