Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Electric Arc Furnace: the Héroult Series-Arc Steel Furnace (Stansfield, 1914)
Volt

Dibuat oleh

Volt

4. November 2026SE
18
0
0
0
0

Electric Arc Furnace: the Héroult Series-Arc Steel Furnace (Stansfield, 1914)

Héroult's steel furnace: a tilting hearth like an open-hearth furnace, lined with dolomite, with two carbon electrodes coming down through the roof. The current goes down one electrode, arcs into the slag, passes through the molten steel and arcs back up the other, so the heat goes straight into the metal. Result: an electric steel furnace about 7 x 4 ft inside for a 3 ton charge, run at about 350 kW and 110 V. Source: A. Stansfield, The Electric Furnace, 2nd ed. (1914), pp. 115-116, 214-216. Unknown: case and tilting gear details, electrode size. Picture: a drawn diagram (Fig. 93 is blank in the scan).
Ahli
Unknown

Instruksi

1

Build the case and lining

Build the furnace in a steel case on a tilting mounting, about 7 x 4 ft inside, with charging doors at the ends. Line it with dolomite bricks and crushed dolomite; dolomite or magnesite on the hearth, which allows strongly basic slags. Ours: mild steel plate. Not given: the case and tilting gear, the bricks' making.

Material untuk langkah ini:

Pelat baja lunakPelat baja lunak1 case
Dolomit (batu kapur magnesia)Dolomit (batu kapur magnesia)1 lining and crushed dolomite
Balok MagnesitBalok Magnesit1 hearth, if magnesite

Alat yang dibutuhkan:

Mesin las busurMesin las busur
Sendok semenSendok semen
Dimensi tidak diketahuiDimensi tidak diketahui
2

Make the removable roof

Make the roof of silica brick, covered with steel plates and given eyes so it can be lifted off. Between the two electrode holes use bronze plates instead of steel, because steel there would raise the inductance of the AC circuit. Fit water jackets round each electrode hole for a close fit, so less heat escapes and the electrodes do not burn in the air. Ours: copper tube for the water jackets. Silica brick has no head here.

Material untuk langkah ini:

Bahan tidak diketahuiBahan tidak diketahui1 silica brick
Pelat baja lunakPelat baja lunak1 roof plates
Lembaran perungguLembaran perunggu1 plates between electrodes
Pipa tembagaPipa tembaga1 water jackets

Alat yang dibutuhkan:

Mesin las busurMesin las busur
Mesin Bor DudukMesin Bor Duduk
AirAir
3

Hang the electrodes

Use two vertical carbon electrodes, square in section. Carry each in a holder on an arm supported by the furnace itself, so its height does not change when the furnace tilts: four contact pieces round the electrode, drawn tight by a steel strap and a screw in the arm, with the cable bolted to them. Raise and lower each electrode separately, by a regulator controlled by the voltage between it and the metal. Not given: electrode size, the regulator's build.

Material untuk langkah ini:

Elektroda karbonElektroda karbon2 electrodes
Logam tidak diketahuiLogam tidak diketahui1 holders, arms, contact pieces

Alat yang dibutuhkan:

Mesin Bor DudukMesin Bor Duduk
4

Melt and refine a charge

Charge steel scrap with some iron ore and lime. Keep each electrode a little above the slag, leaving room for its arc. Regulate the current by hand while the scrap melts, then switch to automatic; full power only after about an hour. Pour off the slag and make a second, then a third, with lime and a little sand and fluorspar, before the final additions. At La Praz this took about 350 kW at 110 V: 5 hours for 1.25 tons of low-carbon steel, 8 hours for 2.33 tons of high-carbon steel. Not given: the electric supply.

Alat yang dibutuhkan:

AirAir

Bahan

8

Alat yang Diperlukan

5

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...