Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Electric Kettle: Immersion Heater with a Steam and Switch-On-Dry Cut-Out (Taylor, US 4,358,666)
Ed

Dibuat oleh

Ed

9. November 2026FI
10
0
0
0
0

Electric Kettle: Immersion Heater with a Steam and Switch-On-Dry Cut-Out (Taylor, US 4,358,666)

An automatic electric kettle boils water with an immersion heater and switches itself off. J. C. Taylor (US 4,358,666, 1982) mounts one control on the heater's head: a bimetal disc touching the hot head cuts the power if the kettle is switched on dry, and a second bimetal disc in the steam trips an over-centre lever that cuts it when the water boils. In his kettle (Fig. 14) the steam leaves through a hole high in the wall and runs down a passage between the handle and the wall to the control. A knob resets it. Source: J. C. Taylor, US Patent 4,358,666 (filed 1980, granted 1982). Picture: its Fig. 14.
Lanjutan
Unknown

Instruksi

1

Read Taylor

"The effect is that when the water boils, the lever 16 is tripped by the actuator 22 from its first to its second position, thus interrupting the supply of electricity to the heating element."
2

Fit the immersion heater

Make the kettle body with a spout, lid and handle, an opening low in the back wall for the heater head and a hole high in the wall under the handle for steam. Fix the immersion heater's head watertight in the low opening, with its element low in the kettle and its hot return brazed to the head so the head heats up if the element runs dry. Form a steam passage between the handle and the wall from the high hole down to the head. Body material, size and heater rating are not given.

Material untuk langkah ini:

Logam tidak diketahuiLogam tidak diketahui1 kettle body
Elemen pemanasElemen pemanas1 immersion heater

Alat yang dibutuhkan:

Obor patri kerasObor patri keras
Mesin Bor DudukMesin Bor Duduk
Set Mata BorSet Mata Bor
Metode pembentukan tak diketahuiMetode pembentukan tak diketahui
Dimensi tidak diketahuiDimensi tidak diketahui
3

Build the switch-on-dry unit

On the head mount a switch unit with three pins (line, neutral and earth) for the kettle lead's socket. Wire the line pin to one cold end of the element through a movable contact on a springy conductive strip and a fixed contact. Rivet the tongue of a snap-acting bimetal disc to a pillar so its body touches the head. Fit a sliding link that the disc pushes: at about 120 °C (Taylor: "say 120° C.") the disc snaps over and the link parts the contacts.

Material untuk langkah ini:

Bahan isolasi tidak diketahuiBahan isolasi tidak diketahui1 switch unit body
Logam tidak diketahuiLogam tidak diketahui1 pins, contacts and strip
Bilah bimetalBilah bimetal1 dry-switch disc

Alat yang dibutuhkan:

Mesin Bor DudukMesin Bor Duduk
Set Mata BorSet Mata Bor
4

Make the steam unit

Press a disc of sheet bimetal into a domed die, with a cut-out that leaves a tongue in the middle, so it snaps over when steam heats it. Mount it by its rim on a lever that rocks on two knife edges in notches of a body seated over the switch unit, held by two over-centre C-springs, with a shroud round the pins and a steam opening sealed by an O-ring. A finger of the lever passes through the sliding link; a knob on the lever comes out through the housing. The trip temperature and bimetal grade are not given.

Material untuk langkah ini:

Bilah bimetalBilah bimetal1 steam disc
Bahan isolasi tidak diketahuiBahan isolasi tidak diketahui1 steam unit body and lever
PegasPegas2 C-springs
O-ringO-ring1 buah

Alat yang dibutuhkan:

Metode pembentukan tak diketahuiMetode pembentukan tak diketahui
5

Close up and use

Screw the outer housing over both units into the threaded pillars, the knob through its opening and the steam passage meeting the steam unit's channel. Fill, plug in the lead and press the knob down to close the contacts. When the water boils, steam reaches the disc, the lever snaps over and the power goes off; switched on dry, the head heats and the other disc cuts it and holds the lever off. Press the knob to reset.

Material untuk langkah ini:

Bahan isolasi tidak diketahuiBahan isolasi tidak diketahui1 outer housing
Kabel lentur berstekerKabel lentur bersteker1 kettle lead with socket

Bahan

7

Alat yang Diperlukan

5

Cetak biru ini membuat

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...