SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Equal-Arm Balance on a Knife Edge, with a Set of Brass Weights
Penny

Dibuat oleh

Penny

14. Oktober 2026DK
23
0
0
0
0

Equal-Arm Balance on a Knife Edge, with a Set of Brass Weights

The oldest weighing machine is a beam with equal arms balanced on a pivot, a pan hanging from each end: put the load in one pan and known weights in the other until the beam lies level. Balances go back to the Fourth Dynasty of Egypt. A hardened knife edge makes it sensitive and a long pointer shows the smallest tilt; the weights are cast in brass and adjusted against each other. The picture: our diagram of the balance, its knife edge, pointer, pans and weights.
Menengah
Two to three days

Instruksi

1

Beam and knife edge

File a straight beam from flat tool steel with a hole exactly in the middle and one near each end, the two end holes equally far from the centre. Forge and file a short steel knife edge, harden and temper it, and fit it through the centre hole, edge down. File a long pointer onto the beam.

Material untuk langkah ini:

Batang baja perkakas pipihBatang baja perkakas pipih1 buah

Alat yang dibutuhkan:

Kikir LogamKikir Logam
Bor tanganBor tangan
Jangka Sorong Digital 6 InciJangka Sorong Digital 6 Inci
Perapian pandai besiPerapian pandai besi
Ember pendingin tempaEmber pendingin tempa
Kacamata pengamanKacamata pengaman
2

Stand and bearing

Make an upright stand of hardwood with a hardened steel V-block on top, shallower than the knife edge, so the beam rocks freely. Mark a zero line behind the pointer.

Material untuk langkah ini:

Lis kayu kerasLis kayu keras2 buah
Batang Baja LunakBatang Baja Lunak0.3 m

Alat yang dibutuhkan:

Kikir LogamKikir Logam
Perapian pandai besiPerapian pandai besi
Ember pendingin tempaEmber pendingin tempa
3

Pans

Cut two equal brass discs, dish them slightly, drill three holes in each rim and hang each from an end hole on three equal cords.

Material untuk langkah ini:

Lembaran KuninganLembaran Kuningan1 buah
Benang linen berlilinBenang linen berlilin3 m

Alat yang dibutuhkan:

Gunting sengGunting seng
Bor tanganBor tangan
Kikir LogamKikir Logam
4

Trim to level

With both pans empty, file the heavier side until the pointer rests on zero. Swap the pans and check again: if the pointer moves, the arms are unequal and the end holes need moving.

Alat yang dibutuhkan:

Kikir LogamKikir Logam
5

Cast the weights

Melt brass and cast a row of plain cylinders a little heavy in green sand.

Material untuk langkah ini:

Gumpalan kuninganGumpalan kuningan2 kg
ArangArang1 as required
Pasir cetakPasir cetak5 kg

Alat yang dibutuhkan:

Perapian pandai besiPerapian pandai besi
Kowi Tanah Liat Tahan ApiKowi Tanah Liat Tahan Api
Penjepit KowiPenjepit Kowi
Rangka cetak pasir (atas dan bawah)Rangka cetak pasir (atas dan bawah)
Sarung tangan lasSarung tangan las
6

Adjust the weights

Balance the largest weight against a litre of water measured in the cylinder (one kilogram, our reference), filing it down until the beam is level. Make the smaller ones by balancing pairs against a larger one and against each other, filing each to level.

Material untuk langkah ini:

AirAir1 liter

Alat yang dibutuhkan:

Gelas ukurGelas ukur
Kikir LogamKikir Logam
7

A binary set of weights

Memuat notebook Jupyter…
8

Limits

The balance's form and use are as Wikipedia describes; the sizes and the water reference are ours. Water's density changes a little with temperature, so the reference is good to a few parts in a thousand.

Bahan

9

Alat yang Diperlukan

12

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...