Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Gas Burner: a Home-Made Bunsen Burner from Brass Tube (Work, 1892)
Charlie

Dibuat oleh

Charlie

7. November 2026DE
11
0
0
0
0

Gas Burner: a Home-Made Bunsen Burner from Brass Tube (Work, 1892)

A Bunsen burner: gas from a fine jet draws air in through two holes at the foot of an upright tube, and the mixture burns at the top with a hot blue flame that leaves no soot. H. B. Stocks (Work, 1892) makes one from a 3 1/2 in. brass tube 1/2 in. across, a short 3/8 in. tube for the gas, a brass boss and elbow from a gas bracket, and a bit of fine-bore tube from an old oil-can as the jet. A sliding brass collar over the air-holes sets the flame. Source: H. B. Stocks, How to Make a Cheap Spirit Lamp, Bunsen Burner, Blowpipes, etc., Work No. 167 (28 May 1892), p. 167. Picture: his Figs. 3-4.
Menengah
Unknown

Instruksi

1

Read Stocks

"To make a Bunsen burner the following materials will be necessary:—A piece of brass tube 3 1/2 in. long, 1/2 in. diameter (external); a piece of tube 3/8 in. in diameter, 1 1/2 in. long; a brass boss similar to those on an ordinary bracket, but without a tap; a brass elbow tube; also a piece of tubing with very fine bore (small bit of tube from an old oil-can will do)."
2

Solder the elbow on the boss

Solder the brass elbow-piece onto the brass boss, with the tube that has a screw cut for a gallery uppermost.

Material untuk langkah ini:

Sambungan pipa berulirSambungan pipa berulir2 boss and elbow
Patri timah-timbalPatri timah-timbal1 joint
FluksFluks1 joint

Alat yang dibutuhkan:

SolderSolder
3

Fit the jet

Cut the fine-bore tube 3/4 in. to 1 in. long and solder it inside the vertical tube of the elbow-piece so it projects about 1/2 in. If it is too small for the hole, plug round it with a little sheet lead, keeping it perfectly vertical and in the centre of the outer tube, then solder. The metal of the oil-can tube is not given (unknown).

Material untuk langkah ini:

Logam tidak diketahuiLogam tidak diketahui1 fine-bore tube
Lembaran timbalLembaran timbal1 packing
Patri timah-timbalPatri timah-timbal1 joint

Alat yang dibutuhkan:

SolderSolder
Gunting sengGunting seng
4

Make the burner tube

Take the brass tube 3 1/2 in. long, 1/2 in. across. If it is not of very thick brass it will be a little too large: turn a piece of very thin sheet brass 1/2 in. by 1 1/4 in. into a cylinder and solder it inside one end. Tap that end inside to screw onto the male thread of the elbow-piece. At the same end drill two holes about 3/8 in. across, exactly opposite each other, their centres 5/8 in. from the end: the air-holes.

Material untuk langkah ini:

Pipa kuningan garis tengah luar 1/2 inciPipa kuningan garis tengah luar 1/2 inci1 3 1/2 in.
Lembaran KuninganLembaran Kuningan1 1/2 x 1 1/4 in.
Patri timah-timbalPatri timah-timbal1 joint

Alat yang dibutuhkan:

Gunting sengGunting seng
SolderSolder
Set pembuat ulirSet pembuat ulir
Pemutar tap ulirPemutar tap ulir
Bor tanganBor tangan
5

Assemble and test

Screw the burner tube onto the elbow-piece and screw the 3/8 in. tube, 1 1/2 in. long, into the side opening. Push the india-rubber tube from the gas supply onto the side tube and light. A purplish-blue flame means air and gas are in the right proportion. A yellow tip means too much gas: plug the hole in the jet slightly.

Material untuk langkah ini:

Pipa kuningan diameter luar 9,5 mmPipa kuningan diameter luar 9,5 mm1 1 1/2 in.

Alat yang dibutuhkan:

Selang KaretSelang Karet
6

Fit the air collar

If the gas burns with a green flame and a hissing noise, the air-holes are too large. Cut sheet brass about 3/4 in. wide and 1 3/4 in. long and drill two holes 3/8 in. across, 1/2 in. from each end (their centres 3/16 in. further in). Turn it into a tube and push it onto the burner tube over the air-holes. Turn it until the two sets of holes do not quite match, so the right amount of air reaches the burner.

Material untuk langkah ini:

Lembaran KuninganLembaran Kuningan1 3/4 x 1 3/4 in.

Alat yang dibutuhkan:

Gunting sengGunting seng
Bor tanganBor tangan

Bahan

8

Alat yang Diperlukan

6

Cetak biru ini membuat

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...