Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Gasholder: Water-Sealed Zinc Gasometer with Balance Weights (Ramsay & Travers, 1898)
Charlie

Dibuat oleh

Charlie

4. November 2026DE
8
0
0
0
0

Gasholder: Water-Sealed Zinc Gasometer with Balance Weights (Ramsay & Travers, 1898)

The laboratory gasometer Ramsay and Travers used to store argon: a zinc bell that rises and falls in a narrow ring of water between two fixed zinc cylinders. Because the water space is only about 2 cm wide, little gas dissolves in it. Weights on cords over pulleys balance the bell, and weights laid on top push the gas out. Result: a water-sealed gasholder of 18 to 180 litres. Source: M. W. Travers, The Experimental Study of Gases (1901), pp. 30 and 105-106. Unknown: sizes and how the zinc is joined. Picture: Fig. 34, the small mercury form of the same design.
Menengah
Unknown

Instruksi

1

Make the fixed cylinders

Make two concentric zinc cylinders on a closed base, leaving a ring-shaped space about 2 cm wide between them for the water. Make the top of the inner cylinder dome-shaped. Bring a gas pipe with a stopcock up through the inner cylinder. Ours: zinc soldered with tin-lead solder. Not given: sizes, how the zinc is joined, the stopcock.

Material untuk langkah ini:

Lembaran sengLembaran seng1 outer and inner cylinders, base
Patri timah-timbalPatri timah-timbal1 seams
Katup tak diketahuiKatup tak diketahui1 gas stopcock

Alat yang dibutuhkan:

Gunting sengGunting seng
SolderSolder
Metode pembentukan tak diketahuiMetode pembentukan tak diketahui
Dimensi tidak diketahuiDimensi tidak diketahui
2

Make and hang the bell

Make the gasholder bell of zinc to fit closely over the inner cylinder and down into the water ring, with a dome-shaped top matching the inner cylinder's, so all the gas can be pushed out. Ramsay and Travers made bells of about 180, 27, 18 and 18 litres. Tie a cord to the top of the bell and pass it over pulleys to a hanging weight, to take the bell's own weight off the gas. Fill the ring with water. To deliver gas, take weight off the cord or lay weights on top of the bell. Not given: the weights.

Material untuk langkah ini:

Lembaran sengLembaran seng1 bell
Patri timah-timbalPatri timah-timbal1 seams
Tali RamiTali Rami1 balance cords
KatrolKatrol2 pulleys
Logam tidak diketahuiLogam tidak diketahui1 balance weights

Alat yang dibutuhkan:

Gunting sengGunting seng
SolderSolder

Bahan

6

Alat yang Diperlukan

4

Cetak biru ini membuat

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...