Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Twin-Saw Table: A Rip Saw and a Crosscut Saw at Opposite Corners, One Motor, Each Depth Set by Tilting the Top (Gottschalk, 1926)
Forge

Dibuat oleh

Forge

13. November 2026NO
8
0
0
0
0

Twin-Saw Table: A Rip Saw and a Crosscut Saw at Opposite Corners, One Motor, Each Depth Set by Tilting the Top (Gottschalk, 1926)

Charles Gottschalk of St. Paul, Minnesota, received US 1,584,028, dated 11 May 1926, for a table saw with two saws. A crosscut saw and a rip saw stand at opposite corners of one table, so either or both can be used without changing blades. An electric motor inside the frame drives both through two chains. The top is hinged twice and lifted by a hand screw at either end, which sets each saw's depth of cut on its own. A lever with wheels lets two people truck the whole machine about. The patent gives no sizes; every size here is ours.
Lanjutan
About 1 week

Instruksi

1

Setting each saw's depth

Memuat notebook Jupyter…
2

Read US 1,584,028

"Inasmuch as the saws are positioned fairly close to the hinges 19 and 23 the movement of the table for one of the saws does not appreciably affect the positioning of the same in regard to the other saw so that the depth of cut of either of the two saws may be adjusted independently or simultaneously if desired."
3

Frame on skids

From 45 x 95 mm pine: two skids 10, 11 1200 mm long; four uprights 12 775 mm long; two top rails 13 1300 mm long, their ends 50 mm past the uprights (17 at the rear, 18 at the front); cross rails 14, 15 between the uprights; a motor bed 52 across the skids. Glue and bolt the joints with carriage bolts, square and level, so the rails' tops stand 820 mm above the floor and 600 mm apart.

Material untuk langkah ini:

Kayu pinusKayu pinus10 buah
Baut kepala bulat leher persegiBaut kepala bulat leher persegi24 buah
Ring RataRing Rata24 buah
Mur Segi EnamMur Segi Enam24 buah
Lem KayuLem Kayu1 buah

Alat yang dibutuhkan:

Gergaji Ukir ListrikGergaji Ukir Listrik
Bor Tanpa KabelBor Tanpa Kabel
Set Mata BorSet Mata Bor
Set mata bor sekopSet mata bor sekop
Kunci InggrisKunci Inggris
Klem batangKlem batang
Siku KombinasiSiku Kombinasi
Meteran GulungMeteran Gulung
4

Turn the two arbors

From 30 mm steel bar turn two arbors 26, 27, each 400 mm long. On one end of each turn a collar 40 mm across and 6 mm thick 30 mm from the end, and screw-cut the last 25 mm M20 on the lathe; turn a loose flange 60 mm across with a 20 mm bore for each. Drill and tap the sprockets' hubs for set screws if they have none.

Material untuk langkah ini:

Batang bulat baja lunakBatang bulat baja lunak2 buah
Mur Segi EnamMur Segi Enam4 buah

Alat yang dibutuhkan:

Mesin Bubut LogamMesin Bubut Logam
Cekam bubut 3 rahangCekam bubut 3 rahang
Pahat bubutPahat bubut
Jangka Sorong Digital 6 InciJangka Sorong Digital 6 Inci
Gergaji BesiGergaji Besi
Mesin Bor DudukMesin Bor Duduk
Set Mata BorSet Mata Bor
Set pembuat ulirSet pembuat ulir
Pemutar tap ulirPemutar tap ulir
Kacamata pengamanKacamata pengaman
5

Mount the arbors and the saws

Bolt two 30 mm flange bearings 28 to the outsides of the rails for each arbor, its centre 30 mm below the rails' tops: the crosscut saw's arbor 27 250 mm from the front ends, the rip saw's arbor 26 250 mm from the rear ends. Push the arbors through so the crosscut saw's threaded end stands out past the left rail and the rip saw's past the right one, seen from the front. Fix a 17-tooth #40 sprocket on each arbor between the rails. Put each 250 mm blade on its collar, the teeth at the top pointing to the front, then the loose flange, a nut and a second nut locked against it.

Material untuk langkah ini:

Bantalan flensBantalan flens4 buah
Gir rantaiGir rantai2 buah
Circular Saw Blade SetCircular Saw Blade Set1 buah
Aneka baut segi enamAneka baut segi enam16 buah
Baut tanam ujung cekungBaut tanam ujung cekung4 buah

Alat yang dibutuhkan:

Kunci InggrisKunci Inggris
Set kunci LSet kunci L
Bor Tanpa KabelBor Tanpa Kabel
Set Mata BorSet Mata Bor
6

Motor and chains

Bolt the motor 51 to its bed between the skids under the arbors, its shaft parallel to them, and fit two 17-tooth sprockets 52 on its shaft, each in line with one arbor's sprocket. Fit a #40 chain 53, 54 from each to its arbor, tensioned by sliding the motor in slotted bolt holes. Have the motor wired to a switch within reach at the front. Oil the chains.

Material untuk langkah ini:

Motor listrikMotor listrik1 buah
Gir rantaiGir rantai2 buah
Rantai rolRantai rol2 buah
Sakelar hidup/matiSakelar hidup/mati1 buah
Oli MesinOli Mesin1 buah

Alat yang dibutuhkan:

Kunci InggrisKunci Inggris
Set kunci LSet kunci L
7

The hinged members and the top

Cut two hardwood members 20, 21 20 x 70 mm, 1340 mm long, to lie flat on the rails; hinge their front ends to the rails' front ends 19 and let them reach 40 mm past the rear 22. Cut the 18 mm plywood top 24 1400 x 800, with a slot over each blade, and hinge its rear edge to the members' rear ends 23. Rout a square groove 35 for the crosscut guide parallel to the crosscut saw and a second groove 200 on its other side, and a groove 42 across the top for the rip guide's bar.

Material untuk langkah ini:

Papan Kayu KerasPapan Kayu Keras2 buah
Lembaran kayu lapisLembaran kayu lapis1 buah
Engsel daunEngsel daun4 buah
Sekrup kayuSekrup kayu40 buah

Alat yang dibutuhkan:

Gergaji Ukir ListrikGergaji Ukir Listrik
Mesin profil kayuMesin profil kayu
Set mata mesin profilSet mata mesin profil
Bor Tanpa KabelBor Tanpa Kabel
Set Mata BorSet Mata Bor
Klem batangKlem batang
Siku KombinasiSiku Kombinasi
Meteran GulungMeteran Gulung
8

The depth screws

Screw a 6 mm steel plate under each rail's projecting end, drilled and tapped M12. Run a 150 mm M12 threaded rod up through each, with a wing nut locked on its lower end as a handle. The rear pair 156 push up under the members' rear ends 22, lifting members and top on the front hinges 19: this sets the rip saw. The front pair 157 pass through holes 58 in the members and push the top alone up on its rear hinges 23: this sets the crosscut saw.

Material untuk langkah ini:

Besi Strip Baja LunakBesi Strip Baja Lunak1 buah
Batang berulirBatang berulir4 buah
Mur sayapMur sayap4 buah
Mur Segi EnamMur Segi Enam4 buah
Sekrup kayuSekrup kayu16 buah

Alat yang dibutuhkan:

Gergaji BesiGergaji Besi
Mesin Bor DudukMesin Bor Duduk
Set Mata BorSet Mata Bor
Set pembuat ulirSet pembuat ulir
Pemutar tap ulirPemutar tap ulir
Kunci InggrisKunci Inggris
9

The guides

Crosscut guide: a hardwood bar 39 sliding in groove 35, with an angle fence 37 pivoted on it at 36 and clamped at any angle by a wing nut 40 through an arc slot 38. Rip guide: a bar 43 sliding in groove 42, held by a hand screw 49 through a plate 50, carrying a fence 45 hinged on a bracket 44 and tilted by a wing nut 67 in an arc slot 47.

Material untuk langkah ini:

Papan Kayu KerasPapan Kayu Keras1 buah
Baut kepala bulat leher persegiBaut kepala bulat leher persegi4 buah
Mur sayapMur sayap3 buah
Besi Strip Baja LunakBesi Strip Baja Lunak1 buah

Alat yang dibutuhkan:

Gergaji Ukir ListrikGergaji Ukir Listrik
Bor Tanpa KabelBor Tanpa Kabel
Set Mata BorSet Mata Bor
Siku KombinasiSiku Kombinasi
10

The truck

Pivot two hardwood arms 60, 61 to the rear ends of the skids at 66, with a wheel 62 on the end of each beyond the pivot. Their front ends 63 are handles sliding in keepers 64 on the front uprights. With the handles down, the wheels are off the floor; lift the handles and the wheels take the weight so the saw can be wheeled away.

Material untuk langkah ini:

Papan Kayu KerasPapan Kayu Keras2 buah
Set roda karetSet roda karet1 buah
Aneka baut segi enamAneka baut segi enam4 buah
Sekrup kayuSekrup kayu8 buah

Alat yang dibutuhkan:

Gergaji Ukir ListrikGergaji Ukir Listrik
Bor Tanpa KabelBor Tanpa Kabel
Set Mata BorSet Mata Bor
Kunci InggrisKunci Inggris
11

Try it

Wind both screw pairs down and check each blade stands square to the top and parallel to its groove. Set the rip saw's depth with the rear screws and the crosscut's with the front screws, each about 10 mm above the wood. Wearing glasses and ear defenders, rip a board along the rip guide, then cut the end off another against the crosscut guide.

Alat yang dibutuhkan:

Siku KombinasiSiku Kombinasi
Meteran GulungMeteran Gulung
Kacamata pengamanKacamata pengaman
Pelindung telinga (penutup telinga, SNR 30 dB)Pelindung telinga (penutup telinga, SNR 30 dB)
12

Troubleshooting

Twin-saw table troubleshooting.

Flow

Loading...
13

History and honest limits

**Charles Gottschalk** of St. Paul, Minnesota, US 1,584,028, dated 11 May 1926, filed 1 August 1921. He claimed a frame with two rails, longitudinal members hinged to the rails at one end, a single top hinged to them at the other, a crosscut saw at one end and a rip saw at the other through the top, and means to oscillate the members and top together, and the top alone, "so as to vary the relative depth of cut of either of said saws". He says a gasoline engine may drive it instead of the motor. His grooves are dovetailed; ours are square. He gives no sizes, speeds or sprocket sizes; all of those are ours.

Bahan

23

Alat yang Diperlukan

21

Cetak biru ini membuat

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...