Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Hand Drill: Double-Acting Push Drill, Spiral Rod and Ratchet Bevel Gears (Olson, US 652,137, 1900)
Forge

Dibuat oleh

Forge

3. November 2026NO
11
0
0
0
0

Hand Drill: Double-Acting Push Drill, Spiral Rod and Ratchet Bevel Gears (Olson, US 652,137, 1900)

A hand drill you work by pushing a handle back and forth. The handle's nut runs on a spiral-grooved rod and spins it one way, then the other. Inside a bulb-shaped casing you hold in your other hand, bevel gears and two sliding ratchet bolts turn that back-and-forth spin into steady rotation of the chuck, so the bit cuts on every stroke. Result: a hand drill that bores continuously in one direction from a push-pull stroke. Source: J. E. Olson, US 652,137 (1900). Unknown: all materials and sizes. Picture: the patent drawing.
Lanjutan
Unknown

Instruksi

1

Make the casing

Make two half-egg-shaped shells, each with a half-round neck at both ends. Put them face to face and hold them together with ferrules pushed over the necks: a hollow bulb that fits the hand. Not given: the metal, sizes.

Material untuk langkah ini:

Logam tidak diketahuiLogam tidak diketahui1 shells, ferrules

Alat yang dibutuhkan:

Mesin Bubut LogamMesin Bubut Logam
Dimensi tidak diketahuiDimensi tidak diketahui
2

Make the spiral rod and handle

Cut a rod with a steep spiral groove or thread. Fit a tube over it with a nut at its lower end that runs in the spiral, and a handle at its upper end. Not given: the pitch, the handle material.

Material untuk langkah ini:

Logam tidak diketahuiLogam tidak diketahui1 rod, tube, nut
Bahan tidak diketahuiBahan tidak diketahui1 handle

Alat yang dibutuhkan:

Mesin Bubut LogamMesin Bubut Logam
Set pembuat ulirSet pembuat ulir
3

Make the gears and ratchet hub

Take four bevel wheels: an upper one bored through the centre and fixed on the lower end of the spiral rod, a lower one the same shape and size, and two side wheels that gear them together. Cut a ring of ratchet teeth on the facing sides of the upper and lower wheels, slanted opposite ways. Make a shaft with a hub (barrel) at its top whose tip runs in the bore of the upper wheel; cut two upright dovetail grooves in the hub, each holding a sliding bolt with its two ends bevelled opposite ways, long enough that one end meets one wheel's teeth while the other end is clear of the other wheel. Ours: steel mitre gears.

Material untuk langkah ini:

Set roda gigi payung (baja, 1:1)Set roda gigi payung (baja, 1:1)2 four bevel wheels
Logam tidak diketahuiLogam tidak diketahui1 shaft, hub, two bolts

Alat yang dibutuhkan:

Mesin Bubut LogamMesin Bubut Logam
Gergaji BesiGergaji Besi
4

Assemble

Inside the casing, set the upper wheel with the spiral rod coming out of the top neck, the hub between the wheels, and the lower wheel turning loose on the shaft. Run the two side wheels on screws through the casing wall as their axles. Bring the shaft out of the lower neck and fix a drill chuck on its end. Ours: a drill chuck.

Material untuk langkah ini:

Logam tidak diketahuiLogam tidak diketahui1 two journal screws
Cekam borCekam bor1 buah

Alat yang dibutuhkan:

Set pembuat ulirSet pembuat ulir
5

Drill

Put a bit in the chuck and set it on the mark. Hold the casing still in one hand, pressing lightly toward the work, and push and pull the handle with the other. Each stroke turns the upper and lower wheels opposite ways; the bolts slide over to engage whichever wheel is turning the cutting way, so the bit turns steadily one way.

Alat yang dibutuhkan:

Set Mata BorSet Mata Bor

Bahan

4

Alat yang Diperlukan

5

Cetak biru ini membuat

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...