Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Lady's Side Saddle: Stuffed Head, Small Off-Head, Bolstered Safe and Leather Girth (Hasluck, Saddlery, 1904)
Tex

Dibuat oleh

Tex

13. November 2026FO
9
0
0
0
0

Lady's Side Saddle: Stuffed Head, Small Off-Head, Bolstered Safe and Leather Girth (Hasluck, Saddlery, 1904)

On a side saddle the rider sits with both legs on the near side, the right knee over a stuffed head in front. This is the side saddle from Paul N. Hasluck's Saddlery (1904): a bought tree with a small off-head, the seat built like the gentleman's saddle but padded higher on the riding side, a quilted (bolstered) safe on the near side, and a thin leather girth that buckles from the saddle. He refers back to the gentleman's saddle for many steps, and so does this blueprint.
Lanjutan
About 4-5 days

Instruksi

1

His sizes in centimetres

Memuat notebook Jupyter…
2

Read Saddlery, ch. III

"The head or point is the part projecting on the side of the saddle in front, over which the rider's knee is placed"; "the safe is the part in front which reaches beyond the saddle, covering the horse's shoulder to keep the rider's clothes from the horse." The tree (Fig. 6) is bought; trees differ in head, seat and cantle.
3

Web the tree and build the seat ground

Get a side saddle tree with a small off-head. Strain the web thoroughly and fit the cross pieces and linen to form a ground for the seat, exactly as for the gentleman's saddle. Cover it with white serge for stuffing, but make the sausage pad on the side where the rider sits nearly twice as thick as on the off side: if the seat ran down steep towards the riding side, the rider could fall. Increase the rounding gradually, sloping it down towards the front; sharp corners there would hurt the rider.

Material untuk langkah ini:

Rangka pelana sampingRangka pelana samping1 buah
Pita tegangPita tegang1 buah
Kain linenKain linen1 buah
Kain serge wolKain serge wol1 buah
Isian wolIsian wol1 buah
PakuPaku1 buah
Benang linenBenang linen1 buah
Malam LebahMalam Lebah1 buah

Alat yang dibutuhkan:

Tang kakatuaTang kakatua
Palu cakarPalu cakar
GuntingGunting
Dua jarum pelanaDua jarum pelana
Penusuk (Uncek)Penusuk (Uncek)
4

Stuff the head

Before covering the seat: cut two pieces of stiff leather the shape of the head, reaching to the bottom on the inside and large enough outside to stitch round the horn. Stitch one firmly on each side, put two or three tacks in the outer one at the bottom, and thin and shape the edges. Shape white serge to the head, round at the top and about 2-1/2 in wider along the sides and as much longer at the top; tack round it with white linen thread, turning the edges in and puckering the top so it bulges when stuffed. Stitch it inside the head to the stitches in the leathers so it covers the edge of the horn, bulging equally all round. Stuff clean carded flock, cut small, from the bottom, pushing it up with the seat awl until firm, plump and smooth; hold it with a few loose stitches back and forth along the sides, top up the centre if needed and level it with the seat awl.

Material untuk langkah ini:

Kulit pelana dan tali kudaKulit pelana dan tali kuda1 buah
Kain serge wolKain serge wol1 buah
Isian wolIsian wol1 buah
Benang linenBenang linen1 buah
Malam LebahMalam Lebah1 buah
PakuPaku1 buah

Alat yang dibutuhkan:

Pisau kulitPisau kulit
GuntingGunting
Penusuk (Uncek)Penusuk (Uncek)
Dua jarum pelanaDua jarum pelana
Besi dudukanBesi dudukan
Palu cakarPalu cakar
5

Cover and stuff the seat

Put serge on the outer side of the small head, nailed at the bottom and turned in along its edge. Put on the serge seat cover as for the gentleman's saddle, but cut it round the stuffed horn, turn the edges under and nail the ends in front; along the small horn, turn in the seat cover's edge and whip it to the turned-in edge of the piece underneath. Cut the slit in the centre and stuff as for the gentleman's saddle. Quilt along the ridge from the near-side horn to the root of the cantle, giving a flat, full, square edge, and the same on the other side; refill and level the centre and both points with the seat awl.

Material untuk langkah ini:

Kain serge wolKain serge wol1 buah
Isian wolIsian wol1 buah
PakuPaku1 buah
Benang linenBenang linen1 buah
Malam LebahMalam Lebah1 buah

Alat yang dibutuhkan:

GuntingGunting
Palu cakarPalu cakar
Penusuk (Uncek)Penusuk (Uncek)
Dua jarum pelanaDua jarum pelana
Besi dudukanBesi dudukan
6

Cover the head and seat in hogskin

Nail hogskin over the long point at the back, pull it tight and tack it close round the top to remove every pleat; leave it to dry. Damp the hogskin seat and put it on, with a small piece of hogskin outside the small point; cut the seat round the long point, cross the ends in front and tack them low. When dry, cut firm leather to fit the hollow at the back of the long point and hogskin about 1/8 in larger all round; shave both and paste them together.

Material untuk langkah ini:

Kulit babi samakKulit babi samak1 buah
Kulit pelana dan tali kudaKulit pelana dan tali kuda1 buah
Lem kanji teriguLem kanji terigu1 buah
PakuPaku1 buah

Alat yang dibutuhkan:

Pisau kulitPisau kulit
Bunga karangBunga karang
Tang kakatuaTang kakatua
Palu cakarPalu cakar
7

Welt the skirts and seat

Fit and mark the skirts as for the gentleman's saddle. Put the thin hogskin welt along the upper edge of the seat and stitch skirt and welt together only as far as the root of the big point, and the same opposite under the short point. From there stitch a wider doubled welt to the skirt to the end. Put a narrow welt round the hole cut for the point with a broad welt on it, and a narrow and broad welt under the short point, and stitch the seat to the hogskin piece there. Tack the ends round the long point neatly under the skirt on the near side.

Material untuk langkah ini:

Kulit babi samakKulit babi samak1 buah
Kulit rok pelanaKulit rok pelana1 buah
Benang kulitBenang kulit1 buah
Lilin tukang sepatuLilin tukang sepatu1 buah

Alat yang dibutuhkan:

Pisau kulitPisau kulit
Penusuk (Uncek)Penusuk (Uncek)
Dua jarum pelanaDua jarum pelana
8

Fit the cover to the head

Remove the long-point cover, put a small welt round the back piece, cover it with hogskin and stitch the cover to it all round without stretching or pleating. Turn the cover inside out, damp it, slip it down over the point and nick the bottom so it sits flat on the seat. Paste between the back piece and the point and press it hard into the hollow; hold it with two or three thicknesses of soft brown leather and a soft rag rolled round until the paste dries. Nail the back piece to the tree at the bottom with two or three tacks out of sight, and cut and stitch the pleats in the seat behind the cantle.

Material untuk langkah ini:

Kulit babi samakKulit babi samak1 buah
Lem kanji teriguLem kanji terigu1 buah
Kulit domba basilKulit domba basil1 buah
Lap katunLap katun1 buah
PakuPaku1 buah
Benang kulitBenang kulit1 buah
Lilin tukang sepatuLilin tukang sepatu1 buah

Alat yang dibutuhkan:

Pisau kulitPisau kulit
Bunga karangBunga karang
Penusuk (Uncek)Penusuk (Uncek)
Dua jarum pelanaDua jarum pelana
Palu cakarPalu cakar
9

Put the seat on the tree

Cover the points running to the panel pockets with thin hogskin or basil, as for the gentleman's saddle. Damp the seat, nail it in front and then at the back, tightening it well round the sides. Nail the hogskin piece behind the short point and pull the welt seam exactly along the edge. Draw the skirt points tightly forward with a tack in the end, the skirt edges under the points; cover the nails and leather ends there, and cut the waste close to the nails all round.

Material untuk langkah ini:

Kulit babi samakKulit babi samak1 buah
Paku pelanaPaku pelana1 buah
PakuPaku1 buah

Alat yang dibutuhkan:

Bunga karangBunga karang
Tang kakatuaTang kakatua
Palu cakarPalu cakar
Pisau kulitPisau kulit
10

Make the near-side flap and bolstered safe

Cut the near-side flap and safe (Fig. 7) as two pieces joined in a straight line, the point side in front: the back part like a saddle flap but a little fuller at the bottom, reaching no farther than the end of the saddle-bar front; the safe running a little beyond the centre at the top. Join them with a closing stitch in strong black wax thread, crossing it every six or seven stitches. For the bolstered safe, cut hogskin the size of the safe plus 1 in all round, quilt and mark it with a small single crease in a regular pattern, and press a design into it. Line it with calico stitched along every mark with white or yellow silk or linen thread, outer lines first, flat and without puckers, pricking a hole in every space. Stuff each space with very fine flock cut small, just enough to show the pattern and feel soft. Fit the cover edge to edge on the safe, crease and prick its edge very fine, stitch the straight edge wrong side out over the joint, turn it over and stitch round the edge double-handed. Paste hogskin on the flap part and stitch it round.

Material untuk langkah ini:

Kulit rok pelanaKulit rok pelana1 buah
Kulit babi samakKulit babi samak1 buah
Kain belacu (calico)Kain belacu (calico)1 buah
Isian wolIsian wol1 buah
Benang linenBenang linen1 buah
Benang kulitBenang kulit1 buah
Lilin tukang sepatuLilin tukang sepatu1 buah
Lem kanji teriguLem kanji terigu1 buah

Alat yang dibutuhkan:

Pisau kulitPisau kulit
Alat pelipatAlat pelipat
Obor PropanaObor Propana
Pahat jahit kulitPahat jahit kulit
GuntingGunting
Penusuk (Uncek)Penusuk (Uncek)
Dua jarum pelanaDua jarum pelana
11

Fit the off-side flap and both flaps

The off-side flap is small, exactly as for a gentleman's saddle but fuller in the rounds below. Make a gullet piece from the front end of the flap to a little over the centre at the top, to be covered by the point of the safe. Nail the off-side flap underneath from the point backwards and above the point in front, and the near-side safe and flap the same way. Where the web hangs down for the straps, punch a hole in the front of the safe close by the tree and near the end of the flap, and turn that part of the flap to the point under the tree, nailing it along the gullet. The girth straps go on the web.

Material untuk langkah ini:

Kulit rok pelanaKulit rok pelana1 buah
PakuPaku1 buah

Alat yang dibutuhkan:

Plong kulitPlong kulit
Palu cakarPalu cakar
Pisau kulitPisau kulit
12

Make the leather girth

Make the thin brown leather girth, which a gentleman's saddle does not have: 3-1/2 ft long and 2 in wide, with a 1 in roller buckle at one end on a chape cut slanting from both sides to its width. Make a loop for it and another about 6 in lower for the overlap of the strap. Cut another piece 1 ft by 2 in with a strap 1 ft 6 in by 1 in stitched to one end; edge and rub the borders and make a narrow hot crease near the edge. Put two rows of cross-stitching on the near side of the girth and two on the off side. It buckles the reverse way to the usual, so it can be adjusted with the rider in the saddle.

Material untuk langkah ini:

Kulit domba basilKulit domba basil1 buah
Gesper rolGesper rol1 buah
Benang kulitBenang kulit1 buah
Lilin tukang sepatuLilin tukang sepatu1 buah

Alat yang dibutuhkan:

Pisau kulitPisau kulit
Alat pelipatAlat pelipat
Obor PropanaObor Propana
Mal sengkelitMal sengkelit
Penusuk (Uncek)Penusuk (Uncek)
Dua jarum pelanaDua jarum pelana
Plong kulitPlong kulit
Meteran GulungMeteran Gulung
13

Nails and panel

Place the tough nails as on a gentleman's saddle: one at each skirt point in front, one through each flap at the point, and one on each side at the narrow end of the skirts behind. Make the panel as in chapter II but slightly wider, to go under the safe in front, and fill the near side rather more.

Material untuk langkah ini:

Paku pelanaPaku pelana1 buah
Kulit domba basilKulit domba basil1 buah
Kain serge wolKain serge wol1 buah
Isian wolIsian wol1 buah
Benang linenBenang linen1 buah

Alat yang dibutuhkan:

Palu cakarPalu cakar
Penusuk (Uncek)Penusuk (Uncek)
Dua jarum pelanaDua jarum pelana
Besi dudukanBesi dudukan
14

Troubleshooting

Side saddle troubleshooting.

Flow

Loading...
15

History and honest limits

From **Saddlery**, edited by Paul N. Hasluck, David McKay, 1904 (archive.org saddlery00hasl), chapter III, "Ladies' Side Saddles", pp. 26-35, Figs. 6-8; every fraction was read on the scan. He gives few sizes of his own here and refers to the gentleman's saddle (chapters I-II) for the web, seat, skirts and panel, as this blueprint does. The leaping head (Fig. 8), quilted skirts, glove pocket (about 4-1/2 by 3-1/2 in) and girth cross straps are not made here. The tools and metric figures are ours.

Bahan

19

Alat yang Diperlukan

14

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...