Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Hearing Protection (Ear Defenders): Rigid Cups on Liquid-Filled Cushions (Shaw & Thiessen, NRC, US 2,801,423, 1957)
Tex

Dibuat oleh

Tex

3. November 2026FO
8
0
0
0
0

Hearing Protection (Ear Defenders): Rigid Cups on Liquid-Filled Cushions (Shaw & Thiessen, NRC, US 2,801,423, 1957)

Ear muffs that seal well and still stop low-pitched noise. Each ear is covered by a rigid cup on a cushion made of a thin PVC tube, emptied of air and part-filled with liquid. Pressed on, the liquid flows round the whole rim and fits the cushion to the head, yet cannot compress, so the cup does not vibrate as a whole and pass the sound in. A sprung headband with a pad holds the cups on ball joints. Result: circumaural ear defenders effective against low-frequency noise. Source: E. A. G. Shaw and G. J. Thiessen (National Research Council of Canada), US 2,801,423 (1957). Unknown: sizes and the attenuation achieved. Picture: the patent drawing.
Menengah
Unknown

Instruksi

1

Make the cups

Make two rigid, non-porous cups to go over the ears, of wood, a hard plastic or a light metal such as aluminium. Widen each rim to about the width of the cushion, and make a small hole in the rim for the cushion's filling nipple. Fix a ball joint on the back of each cup. Not given: sizes.

Material untuk langkah ini:

Bahan tidak diketahuiBahan tidak diketahui2 cangkir
Logam tidak diketahuiLogam tidak diketahui2 ball joints

Alat yang dibutuhkan:

Mesin Bubut LogamMesin Bubut Logam
Dimensi tidak diketahuiDimensi tidak diketahui
2

Make the liquid cushions

For each cup make an endless tube of thin, pliable but non-stretching plasticised PVC, 0.005 to 0.01 in thick, with a filling nipple. Draw out almost all the air, then fill it with liquid to more than a quarter but well under the whole of its cross-section: enough to reach right round the rim when pressed, not so much that it cannot seal. Fix it on the rim with the nipple in the hole. Ours: water as the liquid. Not given: tube size.

Material untuk langkah ini:

Lembaran PVCLembaran PVC1 thin plasticised PVC tube
AirAir1 filling

Alat yang dibutuhkan:

Set alat suntikSet alat suntik
3

Fit the headband and wear them

Make a resilient headband frame with a sponge-rubber pad at its middle and a wire loop at each end. Through each loop pass a threaded stub from the cup's ball joint, with a washer, and tighten with a wing nut. Put the cups over the ears: the cushions take the shape of the head and seal, while the cups stay still against the low-frequency sound. Ours: spring steel for the frame.

Material untuk langkah ini:

Kawat baja pegasKawat baja pegas1 frame and loops
Bahan tidak diketahuiBahan tidak diketahui1 sponge rubber pad
Logam tidak diketahuiLogam tidak diketahui2 threaded stubs
Ring RataRing Rata2 buah
Mur sayapMur sayap2 buah

Alat yang dibutuhkan:

Tang berujung bulatTang berujung bulat

Bahan

7
  • 1 sponge rubber pad
    Placeholder
  • 2 threaded stubs
    Placeholder
  • 1 thin plasticised PVC tube
    Placeholder
  • 1 filling
    Placeholder
  • 1 frame and loops
    Placeholder
  • 2 buah
    Placeholder
  • 2 buah
    Placeholder

Alat yang Diperlukan

4

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...