Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Hot Plate Magnetic Stirrer: Ring Heater over a Relay Magnet on a Shielded Spindle (Hug, US 3,028,476)
Ed

Dibuat oleh

Ed

9. November 2026FI
11
0
0
0
0

Hot Plate Magnetic Stirrer: Ring Heater over a Relay Magnet on a Shielded Spindle (Hug, US 3,028,476)

A laboratory stand that heats a vessel and stirs it at the same time. A motor in the base spins a bar magnet; in Theodore Hug's design (US 3,028,476, 1962) that magnet turns a second, free bar magnet on a spindle inside the hot plate, which in turn spins a coated stirring bar in the vessel. A stainless-steel radiation shield and an air gap keep the ring heater's heat away from the motor. The relay magnet sits about 1/2 in. under the aluminium heat sink: closer, eddy currents in the sink slow the stirring. Source: T. Hug, "Hot Plate and Magnetic Stirrer", US Patent 3,028,476 (filed 1960, granted 1962). Picture: its Figs. 1-2.
Lanjutan
Unknown

Instruksi

1

Read Hug

"Attempts have been made to couple conventional heating means to magnetic stirrers, but the same have proved to be unsuccessful. Thus, the base of a laboratory vessel must be positioned relatively close to the driving rotating magnet ... Moreover, if an appreciable amount of heat from the heating means is transmitted to the motor of the magnetic stirrer, it will drastically reduce the useful operating life of said motor."
2

Build the stirrer base

Make a housing of aluminium (or another non-magnetic material) and mount an electric motor inside with its shaft upright. Fix a permanent bar magnet horizontally on the top of the shaft, just under the housing top. Wire the motor through a rheostat to its cord so the speed can be varied. Sizes, motor rating and how the housing is formed are not given.

Material untuk langkah ini:

Lembaran aluminiumLembaran aluminium1 housing
Motor listrikMotor listrik1 buah
Set magnet batangSet magnet batang1 drive magnet
ReostatReostat1 buah
Kabel lentur berstekerKabel lentur bersteker1 buah

Alat yang dibutuhkan:

Dimensi tidak diketahuiDimensi tidak diketahui
Metode pembentukan tak diketahuiMetode pembentukan tak diketahui
3

Make the radiation shield

Shape a radiation shield of non-magnetic stainless steel so it straddles the top of the housing, on stainless-steel legs (a poor conductor of heat) that stand on the housing top. Bore its centre and fit a threaded spindle there with a nut on each side of the shield. Tap a blind thread in each leg.

Material untuk langkah ini:

Lembaran baja nirkarat - 304Lembaran baja nirkarat - 3041 shield and legs
Batang berulirBatang berulir1 spindle
Mur Segi EnamMur Segi Enam2 buah

Alat yang dibutuhkan:

Gunting sengGunting seng
Mesin Bor DudukMesin Bor Duduk
Set Mata BorSet Mata Bor
Set pembuat ulirSet pembuat ulir
Metode pembentukan tak diketahuiMetode pembentukan tak diketahui
4

Fit the relay magnet

Bore a blind cavity in a hub of non-magnetic material so it turns freely on the spindle. Lay a permanent bar magnet 1/4 in. by 1 in. by 1 3/4 in. on top of the hub and hold it with a strap screwed to the hub. The hub and strap material is not given.

Material untuk langkah ini:

Set magnet batangSet magnet batang1 relay magnet, 1/4 x 1 x 1 3/4 in.
Bahan tidak diketahuiBahan tidak diketahui1 hub and strap
Sekrup mesinSekrup mesin2 buah

Alat yang dibutuhkan:

Mesin Bubut LogamMesin Bubut Logam
Mesin Bor DudukMesin Bor Duduk
Set Mata BorSet Mata Bor
Set pembuat ulirSet pembuat ulir
5

Mount the supports

Make three support members of non-magnetic stainless steel, each an upright with flanges. Screw the flanges down into the legs, with small tubular spacers of insulating material round the screws between the shield and the flanges, so air can circulate and carry heat away. Fit a grommet in one support for the heater cord. The spacer material is not given.

Material untuk langkah ini:

Lembaran baja nirkarat - 304Lembaran baja nirkarat - 3041 three supports
Sekrup mesinSekrup mesin3 buah
Bahan isolasi tidak diketahuiBahan isolasi tidak diketahui3 tubular spacers

Alat yang dibutuhkan:

Gunting sengGunting seng
Mesin Bor DudukMesin Bor Duduk
Set Mata BorSet Mata Bor
6

Fit the heater and top

Mount an annular ring heater (elements in a non-magnetic sheath) coaxial with the spindle; join its cord wires to its threaded stud between two nuts. Above it lay an aluminium heat sink, a flat plate wider than the heater, so the relay magnet is about 1/2 in. below it. Cover with a top plate of aluminium or stainless steel whose edge is spun into an inverted dish, and screw the edge to the tops of the supports. The patent claims a blackened outer surface on the heat sink and top plate (how is not given). In use, set the hot plate on the stirrer and put a stirring bar (a short bar magnet sealed in glass or coated with PTFE) in the vessel: the drive magnet turns the relay magnet, which turns the bar.

Material untuk langkah ini:

Elemen pemanasElemen pemanas1 ring heater
Kabel lentur berstekerKabel lentur bersteker1 buah
Mur Segi EnamMur Segi Enam2 buah
Pelat AluminiumPelat Aluminium1 heat sink
Lembaran aluminiumLembaran aluminium1 top plate
Sekrup mesinSekrup mesin3 buah

Alat yang dibutuhkan:

Alat spinning logamAlat spinning logam
Mesin Bubut LogamMesin Bubut Logam
Mesin Bor DudukMesin Bor Duduk
Set Mata BorSet Mata Bor

Bahan

13

Alat yang Diperlukan

8

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...