Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Industrial Air Compressor: a Converted Motorcycle Engine, Motor-Driven (Shop Notes, 1919)
Emma

Dibuat oleh

Emma

4. November 2026SE
7
0
0
0
0

Industrial Air Compressor: a Converted Motorcycle Engine, Motor-Driven (Shop Notes, 1919)

A workshop compressor driven by a 1 hp electric motor: an old single-cylinder motorcycle engine rebored and run as a pump, its exhaust port blanked, its own automatic inlet valve taking in air, and a ball check valve in the spark-plug hole sending air to a tank. Source: Popular Mechanics Shop Notes for 1919, pp. 3166-3167. Unknown: tank, belt and sizes. Picture: the article's drawing.
Menengah
Unknown

Instruksi

1

Recondition the cylinder

Rebore the old engine and fit a new piston for good compression. Remove the exhaust valve and bolt a steel plate, with a gasket under it, over the exhaust port. Leave the automatic inlet valve as it is: it now draws in air.

Material untuk langkah ini:

Bahan tidak diketahuiBahan tidak diketahui1 old motorcycle engine
Rakitan piston dan batangRakitan piston dan batang1 new piston
Pelat baja lunakPelat baja lunak1 blanking plate
Paking perapatPaking perapat1 buah
Baut kepala segi enam - mutu 8.8Baut kepala segi enam - mutu 8.81 buah

Alat yang dibutuhkan:

Batang bor dalamBatang bor dalam
Mesin Bubut LogamMesin Bubut Logam
Bor tanganBor tangan
Kunci InggrisKunci Inggris
2

Fit the outlet

In place of the priming cock on top of the cylinder (the drawing shows it screwed into the spark-plug hole) fit a ball-valve hose connection, and run its hose to the air tank.

Material untuk langkah ini:

Katup periksa bolaKatup periksa bola1 buah
Selang anginSelang angin1 buah
Bahan tidak diketahuiBahan tidak diketahui1 air tank

Alat yang dibutuhkan:

Kunci InggrisKunci Inggris
3

Fit the drive and mount it

Fit a longer main shaft and key an ordinary shaft pulley on its end. Leave the old flywheel in place for momentum. Bolt steel lugs to the floor and fasten the engine base to them. Belt it to a 1 hp, 110 volt motor, and put oil in the crankcase for splash lubrication.

Material untuk langkah ini:

Batang Baja LunakBatang Baja Lunak1 longer main shaft
KatrolKatrol1 buah
Pelat baja lunakPelat baja lunak1 floor lugs
Baut kepala segi enam - mutu 8.8Baut kepala segi enam - mutu 8.81 buah
Motor listrikMotor listrik1 1 hp, 110 V
Oli MesinOli Mesin1 buah

Alat yang dibutuhkan:

Mesin Bubut LogamMesin Bubut Logam
Kunci InggrisKunci Inggris

Bahan

11

Alat yang Diperlukan

4

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...