Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Injection Moulding Machine: Twin Intermeshing Screws as Plasticiser and Ram (Baigent, US 2,916,769)
Emma

Dibuat oleh

Emma

9. November 2026SE
10
0
0
0
0

Injection Moulding Machine: Twin Intermeshing Screws as Plasticiser and Ram (Baigent, US 2,916,769)

An injection moulding machine melts plastic granules in a heated barrel and forces the melt into a mould. K. H. Baigent (US 2,916,769, 1959) does both jobs with one pair of intermeshing screws: turning, they melt, mix and pack the plastic at the nozzle; pushed forward by a hydraulic piston, they act as the ram. Two screws are used because a single screw pushed as a ram lets too much melt flow back along its thread. At the outlet end each of his screws' threads nearly fills the gap in the other's, which seals against backflow. Source: K. H. Baigent, "Injection Moulding Machines", US Patent 2,916,769 (filed 1957, granted 1959). Picture: its Figs. 7-9.
Lanjutan
Unknown

Instruksi

1

Read Baigent

"It has proven, as a practical matter, impossible to use a single screw as both an injection ram and a mixer or plasticiser, since when a single screw is translated forward to force the plastic material through the nozzle, a substantial portion thereof tends to flow backward between the threads of the screw."
2

Cut the twin screws

Cut two intermeshing screws of the same outside diameter all along, so they can slide as a ram. Baigent's example: root diameter about 2.05 in., outside diameter about 3.06 in., pitch 1 in. In the outlet section the thread's outer face is about 0.30 in. deep axially with the leading face sloping 13° to the root, so each thread nearly fills the gap in the other screw. In the inlet section cut the leading face back to 31°, leaving 0.15 in., which gives about 1 1/2 times the swept volume of the outlet. Give each screw a splined end with a tapped bore. Screw length and metal are not given.

Material untuk langkah ini:

Logam tidak diketahuiLogam tidak diketahui2 screws

Alat yang dibutuhkan:

Mesin Bubut LogamMesin Bubut Logam
Mesin FraisMesin Frais
Set pembuat ulirSet pembuat ulir
Dimensi tidak diketahuiDimensi tidak diketahui
3

Make the barrel

Bore a barrel (injection chamber) to take both screws side by side. Bolt a nozzle head on its outer end and screw in the injection nozzle. Cut a feed inlet near the other end under a hopper whose throat has a water-cooling jacket, so the granules do not melt before they enter. Wrap the barrel in closely spaced electric resistance heaters, with one more round the nozzle head. Clamp the barrel to its supports on the base. Bore, metal and heater ratings are not given.

Material untuk langkah ini:

Logam tidak diketahuiLogam tidak diketahui1 barrel, nozzle head and nozzle
Logam tidak diketahuiLogam tidak diketahui1 hopper and water jacket
Elemen pemanasElemen pemanas2 barrel and nozzle heaters

Alat yang dibutuhkan:

Mesin Bubut LogamMesin Bubut Logam
Mesin Bor DudukMesin Bor Duduk
Set Mata BorSet Mata Bor
Set pembuat ulirSet pembuat ulir
Dimensi tidak diketahuiDimensi tidak diketahui
4

Build the sliding drive

Build a gear box that slides on guide rails on a slide bed in line with the barrel. Run a hollow drive shaft for each screw in roller bearings, coupled to its screw by a splined sleeve and a tie rod through the shaft. Key a pinion on each shaft; both mesh inside opposite sides of one ring gear with internal teeth, so the screws turn at the same speed in the same direction. Cut worm teeth round the outside of the ring and drive it with a worm on the upright shaft of a hydraulic motor, in ball bearings.

Material untuk langkah ini:

Logam tidak diketahuiLogam tidak diketahui1 gear box, shafts, pinions, ring and worm
Bantalan rolBantalan rol4 buah
Bantalan PeluruBantalan Peluru2 buah

Alat yang dibutuhkan:

Mesin Bubut LogamMesin Bubut Logam
Mesin FraisMesin Frais
Mesin hobbing roda gigiMesin hobbing roda gigi
Kunci InggrisKunci Inggris
5

Fit the ram cylinder and hydraulics

Bolt a hydraulic cylinder to the frame behind the gear box and bolt its piston rod to the gear box's thrust plate, so screws, gear box and piston slide as one. Feed the cylinder through a spring-loaded check valve, with a second, adjustable check valve on a branch that restricts the return flow: this sets the back pressure the melt must build before the screws are pushed back. An electric motor drives a hydraulic pump from a reservoir, through a solenoid-worked multiway pilot valve that sends oil either to the hydraulic motor or to the cylinder. Put a stop on the gear box and a limit switch where it ends its return stroke, and a time switch for the cooling period. Pressures are not given.

Material untuk langkah ini:

Silinder hidraulikSilinder hidraulik1 buah
Katup searahKatup searah2 buah
Katup solenoidaKatup solenoida1 multiway pilot valve
Motor listrikMotor listrik1 pump drive
Pipa hidrolikPipa hidrolik1 buah
Oli hidrolikOli hidrolik1 buah

Alat yang dibutuhkan:

Kunci InggrisKunci Inggris
6

Run a cycle

Close the nozzle with the mould, fill the hopper with granules or powder and switch on the heaters to bring the barrel up to temperature. Start the hydraulic motor: the turning screws melt the plastic and pack it at the nozzle, and are forced back against the counter pressure until the stop trips the limit switch. The pilot valve then stops the motor and drives the piston forward, so the screws ram the melt into the mould. Everything stands still while the article cools; the time switch then restarts the motor for the next shot. How the mould is clamped and opened is not given.

Bahan

10
  • 1 gear box, shafts, pinions, ring and worm
    Placeholder
  • 2 barrel and nozzle heaters
    Placeholder
  • Placeholder
  • 2 buah
    2 vendors sell this, none ship to you yet
    Placeholder
  • Placeholder
  • Placeholder
  • 1 multiway pilot valve
    1 vendor sell this, none ship to you yet
    Placeholder
  • 1 pump drive
    Placeholder
  • Placeholder
  • Placeholder

Alat yang Diperlukan

8

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...