Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Jigsaw: Motor-Rocked C-Frame on a Leaf Spring (Heese, US 2,692,622, 1954)
Woody

Dibuat oleh

Woody

3. November 2026NO
9
0
0
0
0

Jigsaw: Motor-Rocked C-Frame on a Leaf Spring (Heese, US 2,692,622, 1954)

A small electric jig saw for curved cuts. A long U-shaped frame holds a fine blade stretched between its two arms. The frame's back end hangs on an L-shaped leaf spring, and an eccentric on a motor shaft rocks its lower arm up and down, so the blade saws through a slot in the table while the spring flexes. A wing nut tensions the blade; sawdust falls into a box below. Result: a compact motor-driven jig (scroll) saw. Source: G. O. Heese, US 2,692,622 (1954). Unknown: materials, sizes, the motor and the stroke. Picture: the patent drawing.
Menengah
Unknown

Instruksi

1

Build the base and table

Make a long flat base, wider at the front. Fasten a long upright support along it, its back end a separate upright strip. Across the wide front stand two walls with matching upright guide slots, carrying a level table that overhangs to the front with a slot for the blade. Under the overhang set a removable open box for sawdust. Not given: materials, sizes.

Material untuk langkah ini:

Bahan tidak diketahuiBahan tidak diketahui1 base, support, walls, table, box
Aneka baut segi enamAneka baut segi enam1 fasteners

Alat yang dibutuhkan:

Gergaji BesiGergaji Besi
Bor tanganBor tangan
Dimensi tidak diketahuiDimensi tidak diketahui
2

Make the C-frame and spring hinge

Make a U-shaped blade frame: an upper arm, a lower arm, and a back piece made in one with the lower arm and bolted to the upper. Fix the upright part of an L-shaped leaf spring to the support's back strip; its flat part goes into a slot in the frame's back piece and is held by the same bolt. The frame can now swing up and down on the spring, its lower arm running in the walls' guide slots under the table.

Material untuk langkah ini:

Logam tidak diketahuiLogam tidak diketahui1 frame arms and back
Pegas daunPegas daun1 buah
Aneka baut segi enamAneka baut segi enam1 buah
Mur Segi EnamMur Segi Enam1 buah

Alat yang dibutuhkan:

Kunci InggrisKunci Inggris
3

Fit the motor and eccentric

Fix an electric motor on the wide front of the base with its shaft running across under the frame's lower arm. Put two bolts down through the lower arm, one each side of the shaft; on them hang a lower strip resting on nuts and an upper strip under the arm, with a coil spring on each bolt pushing the strips apart. Fix an eccentric on the motor shaft between the two strips: as it turns it rocks the frame. Not given: the motor, the throw.

Material untuk langkah ini:

Motor listrikMotor listrik1 buah
Bus eksentrikBus eksentrik1 eccentric
Logam tidak diketahuiLogam tidak diketahui1 two strips
Aneka baut segi enamAneka baut segi enam1 two bolts
Mur Segi EnamMur Segi Enam2 buah
Set Pegas TekanSet Pegas Tekan1 two coil springs

Alat yang dibutuhkan:

Kunci InggrisKunci Inggris
4

Fit the blade clamps and use it

On the lower arm fix a strip with a forked end that hooks under the blade's lower pin. On the upper arm fit a bracket with a cross pin; an arm rocks on it, its forked front end over the blade's upper pin, its back end pulled down by a bolt with a wing nut. Add forked guide strips above and below the table. To fit a blade, loosen the wing nut, hook both pins and tighten the nut to stretch the blade straight. Switch on and feed the work across the table. Ours: a pinned coping-saw blade.

Material untuk langkah ini:

Logam tidak diketahuiLogam tidak diketahui1 clamp strips, bracket, arm, guides
Mur sayapMur sayap1 buah
Aneka baut segi enamAneka baut segi enam1 buah
Mata gergaji copingMata gergaji coping1 pinned blade

Alat yang dibutuhkan:

Kunci InggrisKunci Inggris

Bahan

10

Alat yang Diperlukan

4

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...