Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Kitchen Funnel with Air-Vent Ribs, 3D Printed in PETG
3DBonanza

Dibuat oleh

3DBonanza

18. November 2026US
0
0
0
0
0

Kitchen Funnel with Air-Vent Ribs, 3D Printed in PETG

A 120 mm kitchen funnel for bottling wine, cider or juice, printed in one piece in PETG. Three small ribs along the outside of the spout hold it off the bottle neck so air can come out while the liquid goes in, so it pours without glugging. A common, open design; all sizes are ours, and we have not printed or tested it yet.
Pemula
About 4 hours, mostly printing

Instruksi

1

Our funnel's numbers

Memuat notebook Jupyter…
2

Make it fit your bottles

Optional: change TOP_D or the spout sizes and run it in FreeCAD: OUT=. TOP_D= freecadcmd build_all.py
build_all.pypython
"""Batch 2451 -- PETG kitchen funnel with air-vent ribs on the spout. Open, common design (Admiral 2026-11-18: "it is open knowledge on
what a funnel is"); all sizes ours. Run: OUT=<dir> [TOP_D=120] freecadcmd build_all.py  (mm; printed rim-down on the bed, no supports)."""
import math, os
import FreeCAD as App, Part, MeshPart
OUT = os.environ["OUT"]
V = App.Vector
TOP_D = float(os.environ.get("TOP_D", "120"))     # rim inside diameter
WALL = 1.8
CONE_HALF = 30.0                                   # half-angle: 60 degree cone
SPOUT_TOP_D, SPOUT_TIP_D, SPOUT_L = 16.0, 13.0, 50.0   # spout outside, tapering so it fits bottle necks
RIB_H, RIB_W = 1.2, 1.6                            # three vent ribs on the spout's outside
RIM_LIP = 4.0                                      # flat lip round the rim (bed adhesion, stiffness)
r_top = TOP_D / 2
r_neck_in = SPOUT_TOP_D / 2 - WALL
cone_h = (r_top - r_neck_in) / math.tan(math.radians(CONE_HALF))
def save(sh, name):
    bb = sh.BoundBox
    print(name, "valid", sh.isValid(), "solids", len(sh.Solids), "bbox", [round(v, 1) for v in (bb.XLength, bb.YLength, bb.ZLength)],
          "volume_cm3", round(sh.Volume / 1000, 1))
    MeshPart.meshFromShape(Shape=sh, LinearDeflection=0.03, AngularDeflection=0.12).write(os.path.join(OUT, name + ".stl"))
# z up: spout tip at z=0, cone above, rim at the top
off = WALL / math.cos(math.radians(CONE_HALF))
outer = Part.makeCone(SPOUT_TOP_D / 2, r_top + off, cone_h, V(0, 0, SPOUT_L))
inner = Part.makeCone(r_neck_in, r_top, cone_h + 0.01, V(0, 0, SPOUT_L))
spout_o = Part.makeCone(SPOUT_TIP_D / 2, SPOUT_TOP_D / 2, SPOUT_L + 0.01, V(0, 0, 0))
spout_i = Part.makeCone(SPOUT_TIP_D / 2 - WALL, r_neck_in, SPOUT_L + 0.02, V(0, 0, -0.01))
body = outer.fuse(spout_o).cut(inner).cut(spout_i)
lip = Part.makeCylinder(r_top + off + RIM_LIP, 1.6, V(0, 0, SPOUT_L + cone_h - 1.6)).cut(Part.makeCylinder(r_top - 0.5, 3, V(0, 0, SPOUT_L + cone_h - 2)))
body = body.fuse(lip)
r_at = lambda z: (SPOUT_TIP_D + (SPOUT_TOP_D - SPOUT_TIP_D) * z / SPOUT_L) / 2
for a in (0, 120, 240):
    z0, z1 = 2.0, SPOUT_L - 1.0
    pts = [V(r_at(z0) - 0.4, -RIB_W / 2, z0), V(r_at(z0) + RIB_H, -RIB_W / 2, z0), V(r_at(z1) + RIB_H, -RIB_W / 2, z1), V(r_at(z1) - 0.4, -RIB_W / 2, z1)]
    rib = Part.Face(Part.makePolygon(pts + [pts[0]])).extrude(V(0, RIB_W, 0))
    rib.rotate(V(0, 0, 0), V(0, 0, 1), a)
    body = body.fuse(rib)
body = body.removeSplitter()
save(body, "petg-kitchen-funnel")
cap = math.pi * cone_h / 3 * (r_top**2 + r_top * r_neck_in + r_neck_in**2) / 1000
print("cone height", round(cone_h, 1), "mm; holds about", round(cap), "ml in the cone")
print("spout", SPOUT_TOP_D, "->", SPOUT_TIP_D, "mm outside, bore", round(SPOUT_TIP_D - 2 * WALL, 1), "mm at the tip")
print("air gap per rib, in a neck the spout just fits:", RIB_H, "x", "(gap between ribs)")

Alat yang dibutuhkan:

Jangka Sorong Digital 6 InciJangka Sorong Digital 6 Inci
3

Print the funnel

Print it rim down on the bed, no supports; the cone and spout grow upward. PETG sold for food contact, a stainless steel nozzle (brass nozzles can contain lead), 0.2 mm layers, at least 3 walls.
Berkas desainSTLCC0 - Free

Material untuk langkah ini:

Filamen PETGFilamen PETG60 g

Alat yang dibutuhkan:

Pencetak 3D filamen (FDM)Pencetak 3D filamen (FDM)
Set nozel printer 3DSet nozel printer 3D
4

Clean it up

Trim any strings or blobs, especially inside the spout and between the ribs. Check the spout is clear.

Alat yang dibutuhkan:

Pisau KerajinanPisau Kerajinan
5

Check the fit

Put the spout into a bottle: the ribs should touch the neck and leave gaps between them. Pour water through and watch it run without glugging.
Langkah 5 - Image 1

Alat yang dibutuhkan:

Botol kaca bersumbatBotol kaca bersumbat
AirAir
6

Sanitise

Soak it in no-rinse sanitiser mixed as its label says. Do not boil it: PETG softens at about 80 °C.

Alat yang dibutuhkan:

Cairan pembasmi kumanCairan pembasmi kuman
AirAir
7

Troubleshooting

Funnel problems and fixes.

Flow

Loading...
8

Honest limits

A common, open design, drawn by us in FreeCAD; every size is ours. The ribs were checked by slicing the model; the funnel has not been printed or poured through by us yet. Sanitise before every use and replace it when scratched.

Bahan

1
  • Placeholder

Alat yang Diperlukan

7

Berkas desain

1

Cetak biru ini membuat

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...