Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Hind Horseshoe: Round-Pointed Toe, No Seating, Nail Holes in the Front Two-Thirds (Lungwitz and Adams, Text-Book of Horseshoeing, 1913)
Forge

Dibuat oleh

Forge

13. November 2026NO
3
0
0
0
0

Hind Horseshoe: Round-Pointed Toe, No Seating, Nail Holes in the Front Two-Thirds (Lungwitz and Adams, Text-Book of Horseshoeing, 1913)

A flat hind horseshoe from Lungwitz and Adams, A Text-Book of Horseshoeing (1913). It is made "in like manner" as the front shoe, but the branches are bent to a different curve, giving a round-pointed toe, the hoof side is not concaved, and the nail holes run further back. Fitting and nailing the shoe to the horse, calks and clips are not covered here.
Menengah
8-15 minutes a pair, once practised

Instruksi

1

Bar length and sizes

Memuat notebook Jupyter…
2

Read Lungwitz and Adams

"The hind shoe is made in like manner, but the branches are not bent in a circle but given that form shown in Fig. 106."
3

Measure and cut the bar

Measure the hoof from the point of the toe to the buttress and its greatest width; add them for the bar length. Trace the outline on stiff paper if you want to keep it. Cut the bar.

Material untuk langkah ini:

Batang besi tempaBatang besi tempa1 buah

Alat yang dibutuhkan:

Meteran GulungMeteran Gulung
PensilPensil
Lembar kertas tebalLembar kertas tebal
Perapian pandai besiPerapian pandai besi
Pahat potong landasanPahat potong landasan
Penjepit TempaPenjepit Tempa
4

Bend the outer branch to the hind curve

Heat the bar white-hot just beyond its middle and bend it over the sledge head on the anvil face with the turning hammer, as for the front shoe, but bend the branch to the flatter, angled curve of his Fig. 106, not to a circle. The outer branch is made first, the right shoe first in a pair. Draw out the end with the sledge.

Alat yang dibutuhkan:

Perapian pandai besiPerapian pandai besi
Landasan paruhLandasan paruh
Kereta luncurKereta luncur
Palu pembulatPalu pembulat
Penjepit TempaPenjepit Tempa
5

Bevel, flatten and shape

Bevel the branch on the horn, then flatten it. Bending the toe of a hind shoe backs up the inner edge and thins the outer, so hammer the shoe smooth and even. Shape it so the toe is round-pointed, "yet not too much so", as in his Fig. 116.

Alat yang dibutuhkan:

Landasan paruhLandasan paruh
Palu pembulatPalu pembulat
Penjepit TempaPenjepit Tempa
6

Round the inner edge and fuller

Concaving is not necessary: just round the inner edge of the web. Fuller the ground side as for the front shoe, to about two-thirds of the thickness.

Alat yang dibutuhkan:

Landasan paruhLandasan paruh
Fuller (besi pembuat parit)Fuller (besi pembuat parit)
Kereta luncurKereta luncur
Palu pembulatPalu pembulat
Penjepit TempaPenjepit Tempa
7

Stamp the nail holes

Stamp and pritchel the nail holes in the front two-thirds of the shoe, none at the toe: usually one more than a front shoe, seldom more than eight. Set each as far from the outer edge as the wall is thick; on a hind hoof the wall is nearly as thick at the quarters as at the toe.

Alat yang dibutuhkan:

Landasan paruhLandasan paruh
Pelubang panasPelubang panas
Pelubang tapal kudaPelubang tapal kuda
Palu pembulatPalu pembulat
Penjepit TempaPenjepit Tempa
8

Make the second branch and finish

Make the inner branch the same way, turned to the left. Go over the outer edge on the horn and hammer the bearing surface smooth and level. Rough it out in two heats if you can.

Alat yang dibutuhkan:

Perapian pandai besiPerapian pandai besi
Landasan paruhLandasan paruh
Palu pembulatPalu pembulat
Fuller (besi pembuat parit)Fuller (besi pembuat parit)
Pelubang panasPelubang panas
Pelubang tapal kudaPelubang tapal kuda
Penjepit TempaPenjepit Tempa
9

Troubleshooting

Hind shoe troubleshooting.

Flow

Loading...
10

History and honest limits

From **A Text-Book of Horseshoeing**, by A. Lungwitz and John W. Adams, 11th edition, J. B. Lippincott, 1913 (Project Gutenberg 66786), chapter III F. His Fig. 116 shows a hind shoe with toe- and heel-calks; the calks and the toe-clip are not made here, as this chapter gives no method for forging heel-calks or drawing clips. Fitting and nailing are not covered. The metric figures are ours.

Bahan

1

Alat yang Diperlukan

12

Cetak biru ini membuat

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...